SITUATION 2 A wedge of wood having a specific gravity of 0.60 is forced into the water by a 150 lb force. The wedge is 2 feet in width. 11. What is the draft of the wood? 12. What additional force will cause the wedge to be fully submerged? 3 m 150 lb 60°

Q: You have decided to build a deck on your new home 12 feet wide x 16 feet long, using the standard 2…

A:

Q: Determine total indeterminacy and external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+2=5Number of member (m)=8Number of joint…

Q: Jse commands (rectangle, mirror) and List he commands to draw the following drawing start from a…

A:

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: y 130 mm 30 mm 30 mm -40 mm 40 mm-

A:

Q: Determine the centroid of the shaded area shown, which is bounded bythe X axis and the parabola y? =…

A:

Q: 40 fé = 3000psi %3D ダク 26" 14 14 fy = 6o ksi %3D 8#8 12 NWC PMa = ?

A: A beam with T section is given in the above question. The value of fc' and fy is provided. also the…

Q: Determine external and total indeterminacy

A: Given data : Number of external support reaction (R)=2+1=3Number of member (m)=3Number of joint…

Q: Can you help me figure out the different symbols and how many of them are there and put them in…

A: Single Pole Switch Duplex Outlet Quadruplex Outlet Electrical Outlet Fan Outlet Wall Mounted…

Q: -160 40 160 Dimensions 40 in mm 40 -160- –160-

A:

Q: 16m 8m 60° 126m 120m 20m 64m 16m

A:

Q: Q1. Draw N,V &M diagrams 10 kN/m A to B 3m KN 40 2″m 3m 4m

A:

Q: Locate the centroid 10 mm 20 mm 10 mm 10 mm 20 mm 50 mm y

A:

Q: Determine external indeterminacy

A: Given data : Number of external support reaction (R)=2+2+2+2=8

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: entify the outfall entify the peaks entify the valleys

A: Watershed: A watershed depicts an area of land that contains a typical arrangement of streams and…

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: aSN 200 mm 350 mm

A: Free Body Diagram (FBD):

Q: Z 10 mm 15 15 430 y y -y y 15 100 All dimension in mm FIGURE Q3 (a) FIGURE Q3 (b) IN

A: The dimensions of channel section are given.two channel sections are arranged back to back with 10mm…

Q: 643-218

A: Note: As you have nothing mentioned in this problem. So, we are assuming that we have to apply…

Q: show the (c)

A:

Q: Determine degree of external indeterminacy

A: Given data : Number of external support reaction (R)=3+2+2=7

Q: "hat is the degree of indeterminacy of the given Tucture? a. -1 b. 0 С. 1 d. 2

A:

Q: 200 mm 200 mm 400 mm

A: Section  Area  x Remarks  ABC A1  = π42002      = 31400 mm2 x1 = D2    = 2002     =100 mm   AEF…

Q: Locate the centroid y̅ of the area.

A: Draw the figure. From the figure, dA = y dx

Q: 80 38 24 340 R24 25 R40 130

A: It is not possible that every command and steps that is used in the drawing is to write down here…

Q: 5 10 35 30 11E 25 10 15 20 25 .001 in. 10

A: 3 English Fixed scale reading = 0.8inch 4 English Vernier scale = 16 Least count = 0.001 inch Net…

Q: How do I get the support forces

A: The x and y are the vertical and horizontal distances: x=12cos60=6 fty=6sin60=5.196 ft

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.