Situation 10 - Given the following data of the figure shown: Dimensions: L, = 1.80 m L2 = 1.50 m Bar ABC = 100 mm x 20 mm Strut BD = 80 mm × 16 mm L3 = 1.80 m %3D Allowable shear stress of bolts = 70 MPa 51. Compute the allowable load P (kN) if the allowable compressive stress of the strut is 52 MPa. А. 25.7 В. 40.1 С. 35.4 D. 21.3

Situation 10 - Given the following data of the figure shown: Dimensions: L, = 1.80 m L2 = 1.50 m Bar ABC = 100 mm x 20 mm Strut BD = 80 mm × 16 mm L3 = 1.80 m %3D Allowable shear stress of bolts = 70 MPa 51. Compute the allowable load P (kN) if the allowable compressive stress of the strut is 52 MPa. А. 25.7 В. 40.1 С. 35.4 D. 21.3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the allowable bearing stress in the bolt is 18.855 ksi. what is the minimumrequired diameter of the bolt at B? b= .75” h= 7.874” Distances are in feet.
| 10 7.5 D L75X75X6 15 Compute for the: 7.5 C G X=30 Y=70 (d) Normal Stresses (e) Number of rivets from (f) Thickness of Gusset Plate=20mm Diameter of rivet=16mm Allowable Shearing Stress=125 Allowable Bearing Stress=95 (a) Cross sectional Area (b) Axial Forces of the members (c) Indicate if compression or tension shearing Number of Rivets from Bearing of gusset plate and rivets (g) Governing number of rivets per member
A beam shown below has a T-shaped cross section. Determine the location of maximum compressive stress from left support of the beam. I = 87-49 in 4 400 16/ft 16001b 160016 I↓↓↓I LOFT #. £7 32000 lbft 2.914 in 5.886 in B -NA 34/00/6 4FT 10° 100016 -240016 1000lb dc -4000 16 ff V M
i need the answer quickly
Determine the nominal axial compressive strength, Pn for the following cases: a. L= 15 ft b. L = 20 ft Note: Pinned both end support W10 x 33 A992 steel r = 1.94 in E = 29000 ksi L Fy = 50ksi Note: Ag = 9.71 in^2
2. Calculate the internal forces in the bar GF and GD in a roof truss as shownbelow. For each bar, indicate if the internal force is tensile or compressive. Usethe section method (snittmetoden). Point A has simple support and D has rollersupport.
pls show fbd and clear solution for me to follow easily. thanks
Design the shear reinforcement for the given beam below. Use fys = 275 MPa , fy = 415 MPa , fc' = 21 MPa b = 150 mm, d = 325 mm, ds = 10 mm dbt = 16mm , dbc = 12 mm. Column = 300 mm x 300 mm Calculate s in mm (answer should be divisible by 10)
ㅏ 2m 2P 2m B Im 4cm 8cm 4cm 4cm 12cm 4cm An overhanging beam is constructed by four wood plates with rectangular cross-section by nails as shown in the figure. If the allowable stresses are oo-10 MPa and t-1 MPa: a) Determine the load P that the beam can carry safely. b) If each nail can support a shear force of Q=2 kN, determine the required nail spacing e using the load P calculated in question (a).
4. The plate shown in the figure is fastened to thefixed member by seven 10-mm-diameter rivets.Compute the value of the loads P so that theaverage shearing stress in any rivet does notexceed 70 MPa.