10 7.5 L75X75X6 15 Compute for the: 7.5 X=30 Y=70 shearing (f) Number of Rivets from Thickness of Gusset Plate=20mm Diameter of rivet=16mm Allowable Shearing Stress=125 Allowable Bearing Stress=95 (a) Cross sectional Area (b) Axial Forces of the members (c) Indicate if compression or tension (d) Normal Stresses (e) Number of rivets from Bearing of gusset plate and rivets (g) Governing number of rivets per member

10 7.5 L75X75X6 15 Compute for the: 7.5 X=30 Y=70 shearing (f) Number of Rivets from Thickness of Gusset Plate=20mm Diameter of rivet=16mm Allowable Shearing Stress=125 Allowable Bearing Stress=95 (a) Cross sectional Area (b) Axial Forces of the members (c) Indicate if compression or tension (d) Normal Stresses (e) Number of rivets from Bearing of gusset plate and rivets (g) Governing number of rivets per member

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

H Y G F 30 kips 20 30 kips- C D 40 kips 40 kips 40 kips 50 kips 70 kips 4 @ 15'= 60'- (a) Section Method
A lap joint consists of two the same plates with a width of 75 mm and a thickness of 11 mm. it is inter-connected by 4 – 20 mm diameter rivets spaced at equal intervals. Allowable shearing and bearing stresses of the rivets are 110 and 220 MPa respectively.Using A36 steel with Fy = 248 MPa and assuming diameter of hole 3 mm bigger than therivets,a. Determine the capacity due to shear of bolts. b. Determine the capacity due to bearing of rivets on the plates?
Please provide a detailed solution and an illustration please
kindly solve only subpart LETTER D. with a complete solution for verification purposes. Thank you for your assistance!
An electrical resistance strain rosette indicates strains of -400, +800 and +500 along the x, y and 45 axes. What is the shearing strain My ? O A 100 WRONG B 800 C 600 CORRECT D -200
.
1. Present solution in personal handwriting. 2. Present detailed drawings/FBD’s illustrating your solution.
Hand written and clean writing
7. Determine the horizontal shearing stress at 95 mm above the Neutral Axis. 8. Determine the spacing of the bolts.
2. For the figure shown below, determine the following; (60 points) a. Maximum tensile stress b. Maximum compressive stress c. Spacing/pitch of the bolts if the shear force resisted by each bolt is 30 kN 200 mm 100 mm 30 kN/m 10 mm 20 mm |100 kN 15 kN/m 5 kN-m 150 mm C D F 20 mm 3 m 0.5 m 0.5 m 1 m 3 m 20 mm 125 mm
a) The short steel post as shown in Figure 4 is a 152 x 152 UC37 with three compressive loads applied to the top. There is a central load of 200KN and eccentric loads of 'W kN and 100kN. The maximum allowable stress on the face AB is 185 N/mm?. (Area=D47.1cm2,Zxx=273cm) What is the value of the load 'W in kN? WkN A. 152 x 152 UC37 100mm -200KN 50mm 100KN Not to scale Figure 4
Show solutions please. Thanks