qw qw The lap joint with a single shear plane, shown in Fig. is 800 mm wide with four bolts spaced on 200 mm centers. The two plates are each 16 mm thick and the bolts are 18 mm in diameter. Determine the bearing stress on the boltholes, if the applied force q is uniformly distributed over the width of the joint and equal to 150 N/mm. A)416.6 MPa 2 B) 104.2 MPa O C) 58 MPa 2 D) 28.04 MPa

qw qw The lap joint with a single shear plane, shown in Fig. is 800 mm wide with four bolts spaced on 200 mm centers. The two plates are each 16 mm thick and the bolts are 18 mm in diameter. Determine the bearing stress on the boltholes, if the applied force q is uniformly distributed over the width of the joint and equal to 150 N/mm. A)416.6 MPa 2 B) 104.2 MPa O C) 58 MPa 2 D) 28.04 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please provide a detailed solution and an illustration please
check the stress in member BD, DE, and EG using method of sections
Problem 4 The joint is fastened together using two bolts. Determine the required diameter of the bolts if the failure shear stress is Tult = 370 MPa and a bearing stress ultimate is 400 MPa. Use a factor of safety for shear of F.S =2.5. Thickness of the plate is 13mm. 30 mm 80 kN 30 mm 40 kN 40 kN
2. Calculate the internal forces in the bar GF and GD in a roof truss as shown below. For each bar, indicate if the internal force is tensile or compressive. Use the section method (snittmetoden). Point A has simple support and D has roller support.
Steel design. The lap joint shown consist of bolts 22mm in diameter in 25mm diameter holes, The plates are A36 steel with Fy=250MPa, and Fu=400MPa. Use x1=50 mm ,x2= 160mm ,x3=60mm and plate thickness t=12mm for this problem. The allowable stress are: Bearing stress on project are,Fc=1.5Fu Tension on the net area of plates,Ft=0.5Fu Shear on the plates, Fv=0.3Fu Shear strength of bolt,Fv=210MPa Det. the value of Load P based on bolt shear Det. the value of Load P base on bearing on projected area on plate. Det. the value of load P based on block shear
Two 10-mm thick plate members are to be connected using straps of the same thickness and 12-mm diameter rivets as shown in the figure. Determine the maximum bearing stress if the maximum tensile stress on the plate members due to load "P' is 24 MPa. The members are 50-mm wide. Assuming all the rivets fill the holes. Strap Plate Member Plate P. P
Please show your solution on a paper with FBD
A flanged bolt coupling consists of six - ½ inch steel bolts evenly spaced around a bolt circle of 12 inch in diameter, and four – ¾ inch aluminum bolts on a concentric bolt circle 8 inches in diameter. With an applied torque of 260 kips*inch. determine the max shearing stress in the aluminum and steel bolt. Use Gst = 12x10 6 psi and Gal = 4x106 psi
If the allowable bearing stress in the bolt is 18.855 ksi. what is the minimumrequired diameter of the bolt at B? b= .75” h= 7.874” Distances are in feet.
Explain in detail with figures( FBD) and in hand written
Question-02Describe the various types of stresses developed in the shaft AB due to load P acting at the end C as shownin Figure 1.
The pinned joint shown here is held by a 1-cm-diameter pin. The thickness of the two members are t₁ = 0.5 cm and t2 = 1.5 cm. What is the bearing stress when the applied force Fis 150 N? ¹2-F