Situation 1: A flexible cable and rigid boom system is used to lift a load of 65kN at the end of Boom at point C. Points A and B are considered pinned in nature. The allowable shearing stress at all bolts are 25OMPa and the alowable bearing stress at all bolts are 300MPA. Note that the initial position of boom is horizontal and segment A and B are vertical. 1. Determine Ihe Tenslon in each cable. 2. Determine the horizontal reaction at A. 3. Determine the vertical reaction at A. 4. Determine the tensile stress at cable. 5. Determine the tensile stress at threadeu part of cable. 6. Determine the lensile stress at each leg of the turn-buckle. 7. Determine the required diameter of bot in detail 2 due to snear sress. Round off your answer to multiple of 2mm. 8. Using the rounded value of diameter uutained in number 7, determine the required thickness of gusset plate due to bearing. 9. Determine the elongation of cable in mm. Use E = 200 GPa. 10. Determine the vertical displacement at D due to Tension alone. 11. If the temperature wil be increased by 50 deg. Celsius, determine the vertical displacement at C. Use a = 13.2 x 10/°C.

Situation 1: A flexible cable and rigid boom system is used to lift a load of 65kN at the end of Boom at point C. Points A and B are considered pinned in nature. The allowable shearing stress at all bolts are 25OMPa and the alowable bearing stress at all bolts are 300MPA. Note that the initial position of boom is horizontal and segment A and B are vertical. 1. Determine Ihe Tenslon in each cable. 2. Determine the horizontal reaction at A. 3. Determine the vertical reaction at A. 4. Determine the tensile stress at cable. 5. Determine the tensile stress at threadeu part of cable. 6. Determine the lensile stress at each leg of the turn-buckle. 7. Determine the required diameter of bot in detail 2 due to snear sress. Round off your answer to multiple of 2mm. 8. Using the rounded value of diameter uutained in number 7, determine the required thickness of gusset plate due to bearing. 9. Determine the elongation of cable in mm. Use E = 200 GPa. 10. Determine the vertical displacement at D due to Tension alone. 11. If the temperature wil be increased by 50 deg. Celsius, determine the vertical displacement at C. Use a = 13.2 x 10/°C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is 7'-3" long and 4'-2" wide? 7. There are 15 risers in a set of stairs running from the basement to the first floor. Each riser is 7 1/4" high. What is the distance between floors? 8. The distance between two floors is 9'-0 1/2". If 14 risers are to be used in a set of stairs, what is the height of each riser?
D Question 19 Find the area of the figure shown. a=3 cm b= 6 cm Take pie=3.14 Round answer to one decimal place. just write the number without units a
Question 3) On the plate in the figure, the length L is given as L = 18 m . According to this; y 2L L 2L 3 L -- L Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result as m without writing units.) Response: Question 3-B) Find the Y coordinate of the geometric center of the plate . (Enter your result as m without writing units.) Response:
Choose the best
Question 3) The length L is given as L=34 m on the plate in the figure. According to this;Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)Question 3-B) Find the Y coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)
Round off answer to 4 decimal places
Pls help with questions no.24
For the last portion, why do you divide by two?
4. What is the cost of 23' of cable if 34' costs $76.00? (round to nearest dollar)
Q2. A 70 kg skier that moves from rest at A is shown in Figure Q2. Suppose friction can be neglected while the direction of the launching velocity at B and the orientation of the underneath ground are 30° and 40° from a horizontal axis x, respectively, determine: (a) the launching velocity of the skier at B using the formulation of conservation of energy. (b) the distance, s where the skier lands at C by considering motion in x and y axes.
Fluid Force. A swimming pool is filled with fresh water to a depth of 7 feet measured at the deep end. There is not enough water in the pool to reach the shallow end. Assume that the pool is constucted using right angles, except where the bottom of the pool meets the end walls. Use Ah for the height of a typical strip across the face of the wall. 6. The weight density of water is 62.4 lb/ Your anwers should have units: pounds. 4 ft 18 ft 24 ft Declare your variable(s) here. Show your reasoning below: a) find the force on the typical horizontal strip (red) ? b) write an integral for the total force on the (left) wall of the pool
Give the answer of the picture.