sion T in the cable which supports the 1000-lb load with the pulley arrangement shown. Each pulley is free to rotate about its bearing, and the weights of all parts are small compared with the load. Find the magnitude of the total force

Q: A 104.8N tightrope walker stands at the center of the rope such that each half of the rope makes an…

A: Given data:  Weight of the walker (W) = 104.8 N Angle (θ) = 8°, with horizontal Required: The…

Q: Suppose you use an ideal pulley of the type shown in image (a) in the figure below to support a car…

A:

Q: A uniform plank of length 2.00 m and mass 31.0 kg is supported by three ropes, as indicated by the…

A: Given, Mass of the plank (m) = 31.0 kg Weight of the person (W)=680 N d=0.500 m

Q: Determine the magnitude of the components of the force and the lever arm d that would put the…

A: Use the lever principle of balance  That is F1d1=F2d2

Q: The joints of the human body can be studied as levers, as can be the elbow that appears in the…

A:

Q: Give also the free diagram and pkease I need an answer ASAP.

A: Step 1:Weight is 750NCoefficient of static friction is 0.25Coefficient of kinetic friction is…

Q: The figure below shows a claw hammer being used to pull a nail out of a horizontal board where 0 =…

A:

Q: Find the tension in the cable.

A:

Q: Suppose you used an ideal pulley of the type shown in image (e) in the figure below to support a car…

A:

Q: A window washer is standing on a scaffold supported by a vertical rope at each end. The scaffold…

A:

Q: 18 D. From the step ladder shown in the figure, sides AC and CE are each 2.44 m long and hinged at…

A:

Q: The arm in the figure below weighs 35.5 N. The force of gravity acting on the arm acts through point…

A:

Q: The arm in the figure below weighs 35.1 N. The force of gravity acting on the arm acts through point…

A: Apply the torque balance equation about point O.

Q: A 93.9 N force exerted at the end of a 0.32 m long torque wrench produces a torque of 15.7 Nm. What…

A:

Q: A truck weighing 1.21 tons parked on a hill inclined 31.9 deg from the horizontal. Calculate the…

A: A truck weighing 1.21 tons parked on a hill inclined 31.9 deg from the horizontalWe need to find the…

Q: to

A:

Q: the forces on the beam are replaced by an equivalent Force-Position system, determine the distance d…

A:

Q: The two children shown in the figure below are balanced on a seesaw of negligible mass. The first…

A:

Q: Problem 2: The upper leg muscle (quadriceps) exerts a force of FQ = 1100 N, which is ied by a tendon…

A: Given data as per question force FQ  = 1100N

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: 1. a) A 4.2 m long beam (m1 = 35 kg) is attached to a wall by a hinge as shown. A light horizontal…

A:

Q: If we assume that the tip of the mandible hits perpendicular to ground, what is the force on the…

A: Given : length, l = 1.30 mm = 1.3 × 10-3 m Mass, m = 130×10-6 g = 1.30 × 10-7 kg Angular…

Q: A plane is inclined at an angle of 30 degrees from the horizontal surface. A mass of 5kg is kept on…

A: mass m = 5kgangle  g=10 m/s^2

Q: When the palmaris longus muscle in the forearm is flexed, the wrist moves back and forth. If the…

A:

Q: When a child sits on his bigwheel the center of mass of the child and Bigwheel together is 20.0 cm…

A:

Q: As shown below, a sign weighing 353 N is hanging (via a wire) from a uniform 100 N beam of length L.…

A: