Simple electronic circuit Consistsa failure ratef/hr. 4 diodes each having a farluverate of o.Sxió6 fl hr, 3 capacitors each havinga failure rate of o.2*106 FIh, 10 resistorseach having a fuilure rate of 5x10 /hrand 2 Switches each having a failure rate of2x 16 6 Flhr. A ssumrng Connectors and wiringof 6 transistors each having-6are 100% relia ble. Evalae :O the equivalent failure vate and the probablityof the System Surviving loo0 hr and alsolo ooo hr if all Components must operatefor System Success.O Evalute the probabi lity of surviving(o00 hr and loood hr if three identrcalaircuils to those diseribed above areused in parallel and it is assumedthat the System is fully redundant.

The given data's are, Components Number of components Failure rates Transistors 6 λt=10-6 f/hr…

Simple electronic circuit consists of 6 transistors each having a failure rate f/ hr. 4 diodes each having a of 10 faluve rate of o.sxió6 f/ hr, 3 capacitors each havng a failuve rate of 0:2*106 FIh, 1o resistors each having afuilure rate of 5x10 /hr and 2 Switches each having a failure rate of 2x 16 6 Flhr. A ssuming Connectors and wiriing are 100 % Yelia ble. Evalue : O the equivalent failurr rate and the probab'lily of the System Surviving looo hr and also lo coo hr if all Components must operate for for System Success. O Evalute thr probability of Surviving 2. (o00 hr and loood hr if three identrcal aircuits to those diseribed above are used in parallel and it is assumed that the System is fully redundant.

Simple electronic circuit consists of 6 transistors each having a failure rate f/ hr. 4 diodes each having a of 10 faluve rate of o.sxió6 f/ hr, 3 capacitors each havng a failuve rate of 0:2*106 FIh, 1o resistors each having afuilure rate of 5x10 /hr and 2 Switches each having a failure rate of 2x 16 6 Flhr. A ssuming Connectors and wiriing are 100 % Yelia ble. Evalue : O the equivalent failurr rate and the probab'lily of the System Surviving looo hr and also lo coo hr if all Components must operate for for System Success. O Evalute thr probability of Surviving 2. (o00 hr and loood hr if three identrcal aircuits to those diseribed above are used in parallel and it is assumed that the System is fully redundant.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

100nF Input Voltage AC Voltage 1MQ capacitor 5V diode 1N4001 -5 3V At which voltage value will the axis of the output voltage settle? а) Ov b) -8V c) +8V d) -3V What is the peak to peak value of the output voltage? a) -13V b) -8V c) +3V d) 10v What is the appropriate name for this circuit? a) biased positive clamper b) biased negative clamper c) positive clamper d) negative clamper If the diode is positioned in the opposite direction, what type of circuit will the result be? a) biased positive clamper b) biased negative clamper c) positive clamper d) negative clamper
Using second approximation for a diode to calculate the load voltage.
Draw V, for the networks shown below, the diodes are silicon (1) (2) R 1.0 kn +10 V +8 V Vi 0- Vin 0 R Vout 5V -5V -10 V -8 V Diodes are IN914.
-10 V Assuming the diodes to be ideal diodes O D1 and D2 are forward biased O D1 is forward biased and D2 is reverse biased O D1 and D2 are reverse biased O D2 is forward biased and D1 is reverse biased
At 0 degree kelvin the semiconductor behaves as a/an insulator conductor
A 500 ohm resistor is connected to a 12V source at one terminal and a 10V zener diode of 250 mW and a 5K ohm resistor are connected to the other terminal. What is the maximum current of the zener diode?
Find the range of Ix to meet thefollowing conditions of the diode D1 and D2(Assume Von = 0.7V for both diodes).
The output for the following clamping circuit is shown below assuming ideal diode calculate the avarege value and r.m.s value for the output circuit Vm-10. V=5 R (1) Figure 7-2 simple parallel clippers (Ideal diodes) (7-3)
Full wave Bridge Rectifiers Np = 10 Ns = 1 Solve for Vmax, Imax, Vdc, Idc, Vripple
O has more bandwiath The circuit has two oppositely connected ideal diodes in parallel. What is the current flowing in the circuit? 20 www D2 D1 30 ww 40 12V O 1.33 A O 2.0 A O 1.714 A O 2.31 A
complete the table and make a graph using SILICON DIODE. then explain how did you get the values and plot the forward and reverse biased
in the T12. The purpose of adding impurity is to increase either the number of semiconductor crystal.