Signal in Figure 5 is represented by v(t) = 5 sin(2n500t) + 5 sin (2n750t), spanning from t = 0s to t = 5 s. Six samples are taken at t = 0 s, 1 ms, 2 ms, 3 ms, 4 ms and 5 ms for analogue to digital conversion. %3D 10 -2 -6 -8 -10 Time (s) x 10 Figure 5 i. Determine the sampling frequency. ii. Is the signal sampled optimally? Justify your answer. iii. Supposed that the signal is to be converted digitally for an application which requires 1V of resolution or better. Suggest the minimum number of bits required in the analogue to digital conversion. 4. 2. Volts

Signal in Figure 5 is represented by v(t) = 5 sin(2n500t) + 5 sin (2n750t), spanning from t = 0s to t = 5 s. Six samples are taken at t = 0 s, 1 ms, 2 ms, 3 ms, 4 ms and 5 ms for analogue to digital conversion. %3D 10 -2 -6 -8 -10 Time (s) x 10 Figure 5 i. Determine the sampling frequency. ii. Is the signal sampled optimally? Justify your answer. iii. Supposed that the signal is to be converted digitally for an application which requires 1V of resolution or better. Suggest the minimum number of bits required in the analogue to digital conversion. 4. 2. Volts

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

IX) Represent(-52)10in a) Sign Magnitude form and b) Sign 2'sComplementform.
INSTRUCTION: USE5 DECIMAL PLACES What value of R. will the circuit be in resonance given a parallel RLC consisting of X, = 170, Xc = 150, R, = 120, E=150V. And what will be the total current and power under this condition?
please show all work. thank you!
The effective spectrum of a given signal is from 20HZ to 200HZ, to sample this signal one of the following sampling frequencies can be used O 20 Hz 300 Hz O 600 Hz O 200 Hz
3- Analyze the system shown below to find the output waveform, Vout, assume the capacitor voltage value is -1.0 V at t-0 and RC-1 msec. -0.5 -1.0 V(1), V 1.0 0.5 R $ AAA f, msec
Draw a 2 Hz sinus function (amplitude is 2V). Calculate minimum sampling frequency. Draw the sampled signal with a sampling period of t=0.1s
Design with IC ‘555 and a capacitor of 9 uF: Monostable to get signal period=7 Astable to get frequency=2 Constraints: Use any resistor to be between 1K and 50K.
why the frequency fT is called the ? unity gain frequency
Look at image.
For a second order system, natural frequency of oscillation is 10 rad/sec and damping ratio is 0.1. What is the 2% settling time?
Q4) Using Synchronous decade/BCD counter (cont'd).Number of state=10
A carrier signal with frequency of 1 MHz and peak-to-peak amplitude of 10√2v is added to a single tone message with frequency of 1 kHz and peak-to-peak amplitude of 4√2v. Then passed through a diode having the following c/cs: i(t) = e(t) + 0.5e²(t), find: 1- Modulation depth of DSB signal. 2- Frequency of each component in the diode current.