The result from the sieve analysis is shown:Calculate the coefficient of uniformity. Determine the percentage of sand? What is the effective size of the sample (in mm). Sieve SizeSieve opening (mm)Percent Finer3 in.76.2100%2 in.50.890%1 in.25.480%# 44.7575%#102.0060%#200.85040%#500.30030%#1000.15010%#2000.0754%

Given the sieve sizes and percentage finer soil in those sieves.

Answered: Sieve Size Sieve opening (mm) Percent…

Sieve Size Sieve opening (mm) Percent Finer 3 in. 76.2 100% 2 in. 50.8 90% 1 in. 25.4 80% #4 4.75 75% #10 2.00 60% #20 0.850 40% #50 0.300 30% #100 0.150 10% #200 0.075 4%

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: setup in the laboratory, as shown in the igure, where two identical dense sand amples A and B are…

Q: Considering the following measurements, calculate the quantity passing and % retained applicable for…

Q: Situation 3. Following are the results of a sieve analysis. Determine: a. Cu b. Cc c. So Sieve No. 4…

A: To Determine :- a. coefficient of uniformity, Cu b. Coefficient of curvature, Cc c. Sorting…

Q: 3- Following are the results of a laboratory consolidation test on a sample of undisturbed clay…

A: Draw the horizontal line from maximum curvature Draw tangent from the maximum curvature point…

Q: The resistance to membrane expansion (i.e., the results of the dilatometer test that relate to the…

A: The DMT is an in-situ test tool used to assess strength and deformation properties of finely grained…

Q: (e). A field density test was conducted by core cutter method and the following data was obtained:…

A: Data of field density test by core cutter method:-Weight of empty core cutter = W1= 25NWeight of…

Q: Obtain fineness modulus for following sieve analysis data

A: Given: Sieve size (mm) %retained 9.5 0.00 4.75 16.00 2.36 19.00 1.18 12.00 0.6 13.00…

Q: 1 Weight of retained on each sieve. 2. Calculate the fineness modulus for the sanmple. 2. According…

A: Fineness Modulus of a sand sample gives an idea about its grading.Fineness Modulus =Cumulative…

Q: Cummulative Percent SIEVE ANALYSIS GRAPH Weight Retained (g) Retained (%) Sieve Size Percent Percent…

A: Soils are broadly classified as Coarse grained soils and fine grained soils. If more the 50% of soil…

Q: Evaluate the result of sieve analysis for fine aggregates as shown below Mass of soil * based on…

A: Given Seive No, Seive size, mass of soil with and without pan. Required % retained, sum (%retained),…

Q: The mass of the container plus sand inside is 590 g. During the sand specimen preparation, you…

Q: Consider the grain size gradation curve for the soil shown in the image below and classify the soil…

A: Look at the % passing through sieve no 200=20<50%⇒COARSE GRAINED SOIL

Q: he results of sieve analysis are shown below. Sieve No. Opening Size (mm) Mass Retained (g) 4 4.75…

A: Sieve Analysis: It is an analysis done in order to obtain the particle size distribution allowing…

Q: A liquid limit test on a clay was performed with the following results. The natural water content of…

Q: A laboratory test was conducted according to Method A of the ASTM D4318 to find the liquid limit of…

A: The wet mass of the soil sample with the mass of the can is measured, again the dry mass of the…

Q: 1. Forestland clay has a density of 2150 kg/m3 and the values for the volume shape factor and…

Q: a. what is the effective size diameter? b. what is the uniformity coefficient?

Q: 1. 820 g sample of sand was found to have the following amounts retained on each sieve. 630 μm 315…

A: Given- A sieve analysis is performed on sample of sand having total weight of 820g. After performing…

Q: In falling head permeability test the initial head was 350 mm and the final head was 60 mm. The…

A: Given data- Falling head permeability test- Initial head h1=350 mmFinal head h2=60 mmThe…

Q: 2.2 U.S. sieve no. 4 10 20 40 60 80 100 200 Pan Mass of soil retained (g) 0 44 56 82 51 106 92 85 35…

A: Given, Sieve analysis data of soil NOTE : As per guidelines, first question along with all…

Q: A soil sample has a total volume of 1,485 cc. The specific gravity of the soil solids is 2.74. Then…

Q: From the results of a sieve analysis, shown below, determine: (a) the percent finer than each sieve…

Q: e Size 5 mm 5 mm 3 mm 0 mm 0 mm mm mine the Fineness Modulus. Weight reta 0 100 250 350 200 100

A: Given that Dry weight of sample = 1 kg W = 1000 grams Write column of cumulative weight retain(…

Q: A 1000g of sand has been soaked for at least 24hours prior to lab. After drying the sample to…

A: Solution: Given data: i) weight of the sand sample taken = 1000 g ii) W1 = sample 1 + can 1 = 800 g…

Q: Determine the percentage of the following types of soil in the sample;

A: Gravel (4.75mm)- 0 Coarse-grained- 6% medium grained- 15.74% Fine grained- 19.36% Fines- 13.08%

Q: The following results were obtained from a liquid limit test on a clay using the Casagrande cup…

A: Given data Number Of Blows Water Content (%) 6 52.5 12 47.1 20 43.2 28 38.6 32…

Q: Homework 7: A cylindrical clay sample of 38 mm in diameter and 76 mm in height. It was brought from…

Q: In a site consisting of normally consolidated clean sands,the water table is at 10 ft depth. The…

A: Given:- The depth of the water table = 10 ft The average unit weight of the sand above the water…

Q: A series of identical samples have been tested with drained triaxial test and some of the values are…

Q: B. Solve the following problems. Write your answer in a long bond paper. Avoid Erasures. 1. The…

Q: 2.1 The bulk density determined by this test method is for aggregate in an oven-dry condition. If…

A: In soil mechanics, the void ratio describes the relationship between the volume of voids, or spaces,…

Q: The results given in Table 1 were obtained in a particle size distribution test for soil sample…

A: The weight retained of soil is,To find: The gradation curve and its properties.

Q: a) Plot the grain size curve b) Calculate the coefficient of uniformity and the coefficient of…

A: For the given data, the particle size distribution curve is plotted below: a.

Q: Following are the results from the liquid and plastic limit tests for a soil. Liquid limit test: let…

A: liquid limit is taken at 25 number of blows plastic limit is average of test results plasticity…

Q: Question 18 Given below is the result of a sieve analysis done on a soll sample. Sleve No. Diameter…

A: To find out the coefficient of uniformity.

Concept explainers

Soil engineering for highway design

Soil engineering is a part of geotechnical engineering that deals with the characteristics of soil. It also helps to understand the behavior of the soil in different conditions. The basic concepts of soil are studied to check the strength, compressibility, and porosity of the soil. This makes soil engineering an important topic for civil engineering.

Question

100%

The result from the sieve analysis is shown:

Calculate the coefficient of uniformity.

Determine the percentage of sand?

What is the effective size of the sample (in mm).

Sieve Size
Sieve opening (mm)
Percent Finer
3 in.
76.2
100%
2 in.
50.8
90%
1 in.
25.4
80%
# 4
4.75
75%
#10
2.00
60%
#20
0.850
40%
#50
0.300
30%
#100
0.150
10%
#200
0.075
4%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given details

VIEW

Calculation & results

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the Fineness modulus of sand for the results of sieve analysis
Determine the Fineness Modulus of the sand given its sieve analysis in the following table. (round to 2nd decimal place) Weight Retained Sieve (g) 3/8 in. 10 No.4 80 No.8 80 No.16 350 No.30 240 No.50 80 No.100 160
Table 1 summarizes the results of a sieve analyses. • Determine the percent finer than each sieve. ● Plot the particle-size distribution curve. Use the 5-cycle, semi-log sieve paper that is provided as part of this assignment. • Determine D10, D30, and D60 from the grain-size distribution curve. • Compute the coefficient of uniformity (Cu). • Compute the coefficient of curvature (Cc). Table 1: Results of a Sieve Analysis U. S. sieve number Sieve opening (mm) Mass of soil retained (g) 4 4.750 0 10 2.000 41.2 20 0.850 55.1 40 0.425 80.0 60 0.250 91.6 100 0.150 60.5 200 0.075 35.6 pan 21.5
Situation 3. Following are the results of a sieve analysis. Determine: a. Cu b. Cc c. So Sieve No. 4 6 10 20 40 60 100 200 Pan Diameter (mm) 4.760 2.380 2.000 0.840 0.420 0.250 0.149 0.074 Soil Sample Mass Retained (g) 100 180 86 160 105 134 110 65 45
Can u solve ?(readable) A soil specimen is 38 mm in diameter and 76 mm long, and in its natural conditionweighs 168.0 g. When dried completely in an oven, the specimen weighs 130.5 g. The value ofGs is 2.73. What is the degree of saturation of the specimen?
Someone can help me with this one. Please
Determine the shrinkage ratio when the soil sample has a liquid limit of 70%, plastic limit of 50% and the specific gravity of the soil solid is 2.70, determine the shrinkage ratio. Select the correct response: 2.54 2.37 1.37 1.55
Analysis of Results1. Summarize you Hardness results.2. Does the hardness of your sample fall within the expected range?3. How would the water be classified in terms of hardness (soft, moderately hard, hard, etc.)?
The figure and the table below, shows the results of consolidation test for a soil sample, Find the cc value. TI Applied pressure, kPa 25 50 100 200 400 800 Voids ratio 0.634 0.619 0.583 0.523 0456 0383 0.65 0.6 0.55 0.5 0.45 0.4 of 0.35 10 100 1000 PRESSURE 0.15 0.21 0.12 no one 0.30 VOIDS RATIO
An oedometer test is conducted for a soil sample. The sample is consolidated under vertical stress of 50 kPa. The oedometer test finished at 144 min and data are given in table I. The average thickness of the sample is 20 mm. Predict the coefficient of consolidation (cv, in mm^2/min) using Casagrande log t method and Taylor square root of t method. Please use the empty graphical papers.
In a hydrometer test, the results are as follows: Gs=2.55 Temperature of water=25 degree Celsius, and R=41 at 2 hours after the start of sedimentation. What is the diameter, d, of the smallest-size particles that have settled beyond the zone of measurement at that time? Please answer this asap
SITUATION 3. Following are the results of a sieve analysis. SIEVE NO. OPENING (mm) RETAINED 4 4.75 10 2.0 40 20 0.85 60 40 0.425 89 60 0.25 140 80 0.18 122 100 0.15 210 200 0.075 56 PAN 12 a. Find the effective particle size. b. Determine the uniformity coefficient. c. Find the coefficient of curvature.