Shown below, a wire carrying a current of 2.25 A. The wire is present in a magnetic field of flux density 1.6 T, directed to the left. If the length of the wire is 45 cm, find the magnitude and the direction of the induced force on the wire. Select one: a. F= 1.62 Newtons, Out of Page O b. F= 162 mN, to the left O c. None O d. F= 1.62 Newtons, Into the Page Clear my choice B

Shown below, a wire carrying a current of 2.25 A. The wire is present in a magnetic field of flux density 1.6 T, directed to the left. If the length of the wire is 45 cm, find the magnitude and the direction of the induced force on the wire. Select one: a. F= 1.62 Newtons, Out of Page O b. F= 162 mN, to the left O c. None O d. F= 1.62 Newtons, Into the Page Clear my choice B

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the figure is shown a current of 50 A in a wire 120 cm long and at an angle of 45° to a magnetic field of flux density 6.0 x 10 -4 Wb/m2. What are the magnitude and direction of the force on this wire?
Problem : A current 10 ampere flows through the wire having configuration as shown in the figure. Determine magnetic field at P. Magnetic field due to current in the arrangment F E 2 m 4 m 10 A 4 m 2 m
1Electromechanics
The applied MMF to a simple magnetic circuit is 350AT. It was found that the resulting magnetic field denstiy is 0.7 Wb/m². The average length of this magnetic circuit is 1.64ft and its cross sectional area is 4cm². What is the reluctance (in AT/Wb) of the magnetic material of the core?
A 0.5-m length of wire carries a 10-A current perpendicular to a magnetic field. Determine the magnetic flux density needed so that the force on the wire is 3 N.
A magnetic pole face has a rectangular section having dimensions 200 mm by 100 mm. If the total ﬂux emerging from the pole is 150 µWb. a) If the emerging flux of the pole is changed to 100µWb what will be the resultant density?c) When the dimensions of the magnetic pole are changed to 10m and 5m what will be the new density?d) What would happen if the magnetic pole is changed to square?
The length of a magnetic circuit in a moving iron instrument is 300mm.The coil around the soft iron core has 360 turns and takes a current of 1.75A.The core is square in section with sides of 20mm.Take the relative permeability of soft iron as 1100. Determine the magnetomotive force in the core. Determine the field strength. Determine the flux density. Determine the total flux.
Shown below, a wire carrying a current of 1.25 A. The wire is present in a magnetic field of flux density 1.2 T, directed to the right. If the length of the wire is 65 cm, find the direction of the induced force on the wire. B B Select one: O a. O b. None O c. O d. Oe. To the right Into the Page To the left Out of the Page I
A ferromagnetic core is shown below. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.003 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. 1. - 10 cm--- - 20 cm - 15 cm 500 tums 15 cm 15 cm [1.21 A, 0.4 T, 1.2 T]
An electromagnet has an air gap of 3 mm length and the flux density in the gap is 1.257 T. Find the ampere-turns required for the air gap.
a. Plot the direction of flux at the main poles. b. Draw the current direction at the main poles. c. Draw the direction of flux at the auxiliary poles. d. Draw the current direction at the auxiliary poles. e. Show the direction of rotation by drawing a shape.
Figure 1 shows a ring formed with two different materials – cast steel and mild steel. Mild steel has a mean length of 400 mm and an area of 500 mm². Cast steel has a mean length of 300 mm and an area of 312.5 mm2. The magnetisation curve for mild steel and cast steel is shown in Figure 2. Find the total MMF required to cause a flux of 500 µWb in the magnetic circuit. Determine also the total circuit reluctance. 1.8 Cașt steel Cast-steel 1.6 Silicon iron 1.4 Mild steel 1.2 1.0 0.6 Mild stel Cast iron 0.6 Figure 1: Ring arrangement 0.4 0.2 3000 4000 Magnetic field strength, H(A/m) 1000 2000 5000 600ỘI 7000 Figure 2: Magnetization Curve MMF = AT Reluctance = x 10* ΑT/Wb Flux density, B(T)