SHOW YOUR DETARED SOUTIONS: 1.) A MOLD HAVING & VOLUME OF 0.10ff³ WAS FILLED W/MOIST SOIL THE WEIGHT OF THE SOIL IN THE MOLD WAS FOUND TO BE 12.00 16. THE COIL WAS OVEN DRIED AND THE WEIGHT AFTER DRYING WAS 10.501b THE SPECIFIC GRAVITY OF THE SOUD WAS KNOWN TO BE 2.70 a.) DETERMINE THE WATER CONTENT b.) FIND THE HOID RATO c) FIND THE POROSITY d.) FIND THE PEGREE OF SATURATION

SHOW YOUR DETARED SOUTIONS: 1.) A MOLD HAVING & VOLUME OF 0.10ff³ WAS FILLED W/MOIST SOIL THE WEIGHT OF THE SOIL IN THE MOLD WAS FOUND TO BE 12.00 16. THE COIL WAS OVEN DRIED AND THE WEIGHT AFTER DRYING WAS 10.501b THE SPECIFIC GRAVITY OF THE SOUD WAS KNOWN TO BE 2.70 a.) DETERMINE THE WATER CONTENT b.) FIND THE HOID RATO c) FIND THE POROSITY d.) FIND THE PEGREE OF SATURATION

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The following data were measured for the freeze–thaw test, AASHTO T 283. Three samples were…

A: Given that the diameter of samples is 6 in Convert inches to mm D = 6 in. = 150 mm

Q: A concrete beam sample has a width of 5 inches, a depth of 6 inches, and a length of 20 inches. The…

Q: Define the following terms: ( provide the equation and explain what the equation represents). a).…

A: Thank you for asking the question. We are only permitted to respond to three sub-parts at once in…

Q: The mass of the container is 50.25 kg. The mass of the CA sample plus container is 1,151.50 kg.…

A: Given Mass of container 50.25 kgMass of the CA sample plus container is 1,151.50 kg (moist )Mass of…

Q: 5.8 A sample of wet aggregate weighed 297.2 N. After drying in an oven, this sample weighed 281.5 N.…

Q: The nominal maximum size for an aggregate is the standard sieve opening immediately smaller than the…

A: Answer:- Nominal maximum size of an aggregate:- The smallest sieve opening through which the entire…

Q: Q1. Fill the remaining columns for the sieve analysis data given in the table Weight of Empty…

A: Note: Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: TABLE P5.21 Sieve Size, mm 25 19 12.5 9.5 4.75 2.36 Amount Retained, g 0 376.7 888.4 506.2 1038.4…

A: Sieve Analysis : To assess the grain size distribution of soils with a diameter higher than 0.075…

Q: how to draw the beam load for a combined one and two way slab

A: Step 1: Understand the Slab SystemOne-Way Slab: A one-way slab distributes the load to two opposite…

Question

SHOW YOUR DETARED SOUTIONS:
1.) A MOLD HAVING & VOLUME OF 0.10ff³ WAS FILLED
W/MOIST SOIL THE WEIGHT OF THE SOIL IN THE MOLD
WAS FOUND TO BE 12.00 16. THE COIL WAS OVEN
DRIED AND THE WEIGHT AFTER DRYING WAS 10.501b
THE SPECIFIC GRAVITY OF THE SOUD WAS KNOWN TO
BE 2.70
a.) DETERMINE THE WATER CONTENT
b.) FIND THE HOID RATO
c) FIND THE POROSITY
d.) FIND THE PEGREE OF SATURATION

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

Step 2: Explanation

Step 3: Explanation

Solution

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

(c) Asphalt concrete mixture of AC 14 will be used to construct the wearing course layer. The coarse aggregate, fine aggregate and filler are used as materials to produce the asphalt concrete mixture. The aggregate gradation will be blended to fulfill the gradation limit according to JKR standard specification as shown in Table Q1(c)(i). Based on this statement, conclude the result of sieve analysis test of blended aggregate as shown in Table Q1(c)(ii). I Table Q1(c)(i): Gradation specification for AC 14 mixture BS Sieve Size (mm) Percentage passing by weight 28.0 20.0 14.0 10.0 5.0 3.35 1.18 0.425 0.150 0.075 100 90-100 76-86 50-62 40-54 18-34 12-24 6-14 4-8 I Act Go to
Define the following terms: (don’t just provide the equation, explain what the equationrepresents). a). Saturated Surface-Dry condition of aggregate b). Absorption of aggregates c). Free moisture of aggregates. d). What does a negative free moisture mean and why is it important to consider forconcrete design?
1 - show complete solution
5.14 Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained: Volume of bucket = ¹/2 ft³ Weight of empty bucket = 20.3 lb Weight of bucket filled with dry rodded coarse aggregate: Trial 176.6 lb Trial 275.1 lb Questions and Problems 217 Trial 3 78.8 lb a. Calculate the average dry-rodded unit weight b. If the bulk dry specific gravity of the aggregate is 2.620, calculate the percent voids between aggregate particles for each trial.
CapsL 8 A Determine the range of final gradation of selected aggregates to prepare the job mix formula for binder course of a mixing plant according to data indicated in table below? Use the following tolerances: ± 6 % for 4.75 mm and above aggregate sizes, ± 4% for 2.36 and 0.30 mm aggregate sizes, and ± 2 % for 0.075 mm aggregate size. Note: use first try with 30%, 35%, 30% and 5% for groups A, B, C and D, respectively. Sieve Size 25 19 12.5 9.5 4.75 2.36 0.3 0.075 A (30%) Coarse Aggregate 100 99 56 31 4 0 0 0 % Passing B (35%) Natural Sand 100 100 100 100 100 89 15 4.2 C (30%) Crushed Sand 100 100 100 100 92 56 9 5 D (5%) Filler 100 100 100 100 100 100 97 88 Specification 100 90-100 76-90 56-80 35-65 23-49 5 19 39 Job Mix Formula Job Mix Formula Limitation 13.6
Three samples of fine aggregate were taken from the same stockpile and have the properties shown below. Determine in percentage: (a) total moisture content of each sample, (b) free moisture content of each sample, and (c) the average values of each from the stockpile. Measure Wet Mass (g) Dry Mass (g) Absorption (%) A 521.0 491.6 2.5 Sample B 522.4 491.7 2.4 C 523.4 492.1 2.3
I) Two aggregates (Al and A2) were obtained from the field. A sieve analysis was performed on each sample, and the samples (originally 500g in mass) were brought to the oven dry condition (OD) and weighed. Data was obtained for each of the aggregates and is presented in the tables below. (Density of water-1g/cm) Table 1. Results from sieve analysis. Sieve Size Opening (mm) Weight of Aggregate retained (g) A1 A2 3/8" 9.5 No. 4 4.75 65 No. 8 2.36 60 25 No. 16 1.18 100 396 No. 30 0.6 50 No. 50 0.3 118.5 10 No. 100 0.15 75 15 Pan 75 Table 2. Absorption capacity and moisture content data. Al A2 500 g 500 g Field Weight Oven Dry Weight Absorption Capacity (%) 0.7 % 498.5 g 496 g 0.6 % a) Plot the grading curve for each aggregate (x-axis: sieve opening, y-axis: %passing). (Note: In the grading curves, you must show all data points. You can draw the gradation chart using excel or by hand. If you draw by hand, you have to use a ruler. The format of the gradation chart should be same as in the…
Us Standard Sieve No. Sieve Opening (mm) Weight Retained (g) % Retained on Sieve % Passing Sieve 4 4.75 12.7 6.2 93.8 10 2 24.8 12.1 81.7 20 0.85 21.5 10.48 71.24 40 0.425 38.8 18.92 52.33 60 0.25 23.8 11.60 40.73 100 0.15 19.5 9.51 31.23 200 0.074 46.7 22.76 7.463 Minus 200 17.3 8.44 0 Total 205.1 for D10 and D60 calculate the k value utalizing Hazen's approxoimation. c=100
The specific gravity and absorption test (ASTM C128) were performed on fine aggregate. The following data were obtained.Given:Mass of SSD sand = 400.0 gMass of pycnometer with water = 520.0 gMass of pycnometer with water plus sand = 850.0 gMass of dry sand = 397.0 gRequired:a) absorption, in percentb) free moisture if the sand in the stockpile has a moisture content of 3% bbbbbbbbbbbbbb