· PS. PA.Usteet1 = 3mA = 300mm LE = 300G PaC^ Ps =Y-50KNStress steel and aluminum.11VReformationStrain(1• Vertical displacemenmentVAluminumn2 = 4mA = 500mm²E = 706PS^ Pa =of load to

Answered: Image /qna-images/answer/76c055cd-a1b8-4307-b624-1a3586afd1a9.jpg

Answered: Sheet 1.3m A. 300mm Е - зообра Ps L…

Engineering

Mechanical Engineering

Sheet 1.3m A. 300mm Е - зообра Ps L 2.5m Aluminumn L = 4m A = 500mm E = 706PS ^ Pa =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the right by u = 0.6 mm and upward by v = 1.8 mm to new position Q', as shown in the figure. Determine the shear strain y at corner Q' after deformation. Use a 234 mm, b = 462.57 mm, and d = 329 mm. Part 1 * Incorrect. Consider a right triangle with one length of length (a + u) and one leg of length (d + v). a = Calculate the angle a shown in the figure below. i b α 89.74 R b
Question 2 The steel bar has the dimensions shown in Figure 2 below. Determine the maximum axial force P that can be applied if the ultimate normal stress for the steel is 215 MPa and the factor of safety 2.0 is desired. / 3.4 3.2 3.0 2.5 2.4 K 2.2 2.0 1.8 1.6 1.2 1.0 0 0.1 02 (a) Flat bars with holes P. 30 mm 24 mm- 20 mm 60 mm Figure 2 03 04 05 06 07 2r/D 3.2 3.0 2.5 26 K 22 20 1.8 1.6 1.4 12 1.0 r = 15 mm (b) Flat bars with fillets D Did-2 13 13 12 000204000005 0.10 0.12 0.34 0.30 0.15 0.20 0.22 0.24 0.28 0.25 6.30 vid Figure 3: Stress Concentration Factor, K for the Flat Bars
Problem #2: The following tank presents the following data: • External diameter of 16 inches • ½ inch wall thickness • Internal Pressure 600 psi. 12 kip ft ! B 48 kip ft A 16 in. - p = 600 psi For point B, determine: a) The state of normal and shear stresses. b) The maximum and minimum efforts. Indicate the orientation of the principal axes c) The maximum shear stress. Indicate the orientation of the axes for this effort
Show complete solution pls A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length of the pipe is L = 6.0 m. Thechanges in dimension caused by an increase in temperature of 80°C for the:1. Outside diameter 2. Inside diameter 3. LengthNote: All answer must be round off up to 3 decimal places.
Coefficient of expansion αB= 165.10^-7 1/ 0C , solid copper bar diameter 20 mm , It is placed in a steel pipe with an outer diameter of 30 mm with an inner diameter of 2 mm larger than this bar and an expansion coefficient αÇ = 125.10^-7 1 / 0C, and is joined by a rigid plate from the top so that they move together. Find the stresses that will occur in steel and copper when the system is heated with a temperature difference of Δt = 80 0C. (EÇ = 200 GPa, EB = 100 GPa)
The principal stresses at a critical point in plane stress are o and 0.250. The yield stress for the material is oy = 250 MPa. The magnitude of MPa. (Correct up to two decimal places) o that will cause yielding according to the maximum distortion energy theory is
The two angle bars are used to support a tensile load "T". Assume the tensile load to be equally resisted by each angle. 400 mm x 20 mm THK Gusset Plate The steel used is L 6 x 6 x 1. Properties: A = 7096.76 mm? y = 47.244 mm Fy = 248 MPa Fu = 400 MPa b = 152.4 mm b. t = 25.4 mm x = 47.244 mm Effective hole diameter = 25 mm y Use case 2 for shear lag factor. Use NSCP 2015 code. 1. Determine the maximum allowable load that can be carried by the two L6 x 6 x1 based on yielding of the gross section--- 2. Determine the maximum factored load that can be carried by two L6 x 6 x 1, based on the fracture of the effective net area.---- 3. Determine the maximum allowable tensile load that can be carried.------ 4. Determine the maximum factored tensile load that can be carried-- bo
AL: 1₂ The above figure (not drawn to scale) shows a rod made up of two cylindrical sections of the same material. The left cylinder has diameter d, = 30mm and length 4 = 150mm. The right cylinder has diameter dy=10mm and length = 150mm. The rod is subjected to a force F = 50KN. Find the total extension in the rod, AL, given that E = 203kN/mm². Enter your answer in mm to 5 decimal places in the box below: mm -F
Please solve all part
Derive the relationship between critical resolved shear stress and disloca- tion density given below Terss = To + AVPD
B. See figures attached for reference and solve carefully/ellaborately, include the units and draw the diagram. Your works will be appreciated much, Thanks! A rectangular steel bar 0.5 inch thickness by 1.5 inches width and 220 ft long is subjected to a 6000 lbs tensile load acting along its width. Find the deformation along its length and thickness if poison’s ratio is 0.27