shaft carries four masses in parallel planes A, B, C and D in this order along its length. The masses at B and C are 18 kg and 12.5 kg respectively, and each has an eccentricity of 60 mm. The masses at A and D have an eccentricity of 80 mm. The angle between the masses at B and C is 100° and that between the masses at B and A is 190°, both being measured in the same direction. The axial distance between the planes A and B is 100 mm and that between B and C is 200 mm. If the shaft is in complete dynamic balance, determine: 1. The magnitude of the masses at A and D 2. The distance between planes A and D 3. The angular position of the mass at D

Q: The similar links AB and CD rotate about the fixed pins at A and C (Figure 3). If AB has an angular…

A: Given data:- The given value of angular velocity is, ωAB=8 rad/s

Q: The collar is designed to fit loosely around a fixed shaft with a radius of 2 in. Determine the…

A: Radius of Shaft = 2in Coefficient of kinetic friction = μk Radius measured from center of collar to…

Q: Find the moment of inertia about centroidal XX axis

A: Introduction : The given question is related with solids mechanics . The given section is…

Q: 3.16 Three forces of 900 lb, 1000 lb, and 600 lb are acting on a boat. The first force acts due…

A: Note: Dear student as per our company guidelines i am solving first problem only (i.e problem 3.16…

Q: For the structure shown below, the slope deflection equation of the member BA i.e. MBA 40kN- A B d C…

A: Given data- A structure is given as shown- To Find- The slope deflection equation for member BA…

Q: A 63kg beam extends horizontially from the side of a wall.  A 13kg box hangs from the end of the…

A: If we draw the diagram of this particular question than it'll look something like this

Q: 1.) Determine the resultant of the forces acting on the body. 450KN 600KN 2 1 4 200kN 15 12 2 250kN…

A:

Q: 500KN 200mm 100mm C 45° %24

A:

Q: A flat plate is placed normal to a discharging jet of water. The jet discharges water at the rate of…

A: Given- Rate of discharge from jet Q= 0.2 m3/s, Speed of water V= 18 m/s, It is needed to find the…

Q: The 20-lb disk is rigidly attached to the 7-lb bar OA, which is pivoted freely about a horizontal…

A:

Q: GJ ¥37 B'

A:

Q: Determine the moment of inertia about x' axis and x axis. 200 mm 不 1 lomm 29 K A20k

A: The given data: length of section, L=200 mm height of section, H=20 mm (as you have shown in figure)…

Q: 2. 12m le com 1 4m ↓ X Find the moment of inertia of the thin plate of mass, m, with respect to the…

A:

Q: F 35

A:

Q: y F2 30° X.

A:

Q: For the bar system shown, determine the torsional reactions and torsional rotation of point B.

A: Solution: Draw the Free Body diagram:

Q: y 2 m 2 m 2 m 2 m --> X 4 m 4 m

A:

Q: Dynamics Lab is A 7.75-kg uniform disk developed in the attached to the 4.85-kg slender rod AB by…

A: Given:- Mass of disk, mD=7.75 kgMass of slender rod, mR=4.85 kgAngular velocity, =6.00 rad/sAngular…

Q: Rotation of the radially slotted arm shown in the figure below is governed by Ѳ = 0.2t + 0.02?^3,…

A:

Q: Determine the location of the centroid and moment of inertia of a semi-circle of radius 'r' about…

A:

Q: -3.6 m- A 2.7 m 3.6 kN В D 2.7 m 1.5 m E |F 4.8 m

A:

Q: 2) For the given sections shown: 21) determine the distance of the centroldal avis (or neutal axs,…

A:

Q: 360 mm 80 mm 130 mm 130 mm 300 mm 90 mm 280 mm

A: The FBD of the beam will be:

Q: Determine the moment of inertia about the x axis

A: Given:- A shaded figure is given  To determine:- The moment of inertia about the x-axis

Q: A glass tubing consist of 5 vertical stems which are 500 mm apar connected to a single horizontal…

A: Flows, where streamlines are concentric circles and the tangential velocity, is directly…

Q: The 9-cm diameter 20 degrees Celsius water in the figure strikes a plate containing a hole of 7-cm…

A: Given data  D1 = 9cm = 0.09 m  D2 = 7cm = 0.07 m  Assume density of water = 1000 kg/m3

Q: M = 600 N-m 3 1 m 3 m 900 N/m R₁ R₂ Determine the value of EIS at the left end of the overhanging…

A:

Q: Determine the moment of inertia of the section at Z relative to the centroidal axes x0 and y0.…

A:

Q: A motor armature is in running balance when masses of 1.3 kg and 0.75 kg are added temporarily in…

A: A type of elastic collision in which two objects of equal mass initially move in the same direction…

Q: Determine the reaction at the roller support. Determine the moment reaction at the fixed support.…

A:

Q: Consider the portal frame shown in the figure and assume the modulus of elasticity, E = 2.5 x 104…

A:

Q: A jet of water flowing freely in the atmosphere is deflected by a curved, 90 degrees vane. The vane…

A: Fluid mechanics is a vital field of structural designing that arrangements with the designs…

Q: Resolve the 900-N force into a component P along with AB and a component Q perpendicular to AB.

A:

Q: 3 m D W

A:

Q: Determine the moment of inertia of the area about the centroidal x and y axes.

A: Consider the figure,

Q: Locate the center of mass of the homogeneous rod bent into the shape of a circular arc.

A: Given :- Homogeneous rod bent into the shape of a circular arc is given  Radius of the circular arc…

Q: For the mechanism shown, a. Determine the resultant of the three forces. b. Locate the y coordinate…

A: Given data:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.