Please help me with this one. Please use the second photo as reference.Subject: Strength of materialsTopic: Torsion 3- a steel pope ller shaft is to foan&mit 45mwa4 3 H2' without exceeding a sfearing sfress4 50 Mpa tr tuisting thru more tfan 10in a lkrgth g o6 diameters. Compute thepo per diameter if G= 83 G Pa. TORSIONEquations of compatibility – relations between stresses that are compatible withthe deformations.Equations of equilibrium – relations between the stresses resulting from a studyof the equilibrium between externally applied loads and the internal resistingforces over an exploratory section.Torsion Formulas0 = TL/JG0- angle of rotation (radians)T-torque (N-m)L- length (m)J- polar moment of inertia (m")G- modulus of rigidity (N/m)If we wish to express O in degrees, we multiply the right-hand member by the unitfraction, 180°/r rad = 57.3° /radBy replacing the product GO/L by its equivalent value T/J:T = Tp/JThis is called the torsion formula.The formula that determines the maximum shearing stress is a more commonform of the torsion formula. It is obtained by replacing p by the radius r ofthe shaft:Max t = Tr/J1. The stresses must not exceed the shearing proportional limit.2. The formulas are applicable only to circular shafts, either solid or hollow.

Answered: Sfeel prope ller shaft is to foan&mit…

Sfeel prope ller shaft is to foan&mit 45 mw 43 H2 without exceeding oa shearing sfress 750 mpa tr tuisting thru more tfan 1o lergth f o6 diameters. Compute the on per diameter if G= 83 G Pa.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.3.1P

See similar textbooks

Related questions

Q: Describe three causes of permanent ground deformation in steel pipelines.You may use sketches in…

A: Permanent land displacement (PGD) is caused by faults in the soil, landslides, or liquefaction.…

Q: illustrate normal stresses in cross section.

A: Normal stress is the stress component perpendicular to a given surface, such as a cross section of a…

Q: Write the three assumptions regarding the way the moment deforms the material?

A: When a material is subjected to loading or by force couple acting on a plane passing through its…

Q: What did you use for the axis y is the % finer but what is the x axis axis

A: Given:Required:Give the name of x and y axes used in the graph.

Q: A 10 inch long silver wire is stretched to a total length of 11.50 inches. Find the value of strain

Q: For the composite body shown in Figure 3, determine the location of the centroid (7,9) relative to…

Q: An ASTM A615 grade 60 number 10 rebar with a gauge length of 8 in. was subjected to tension to…

A: It is required to determine the stress in the rebar. Here, P is the load and A is the area of the…

Q: The data shown in the following table are from a tensile test of high-strength steel TENSILE-TEST…

A: Given values: Tensile test results for high strength steel. Initial diameter, d=0.505 in Initial…

Q: Which of the following options are correct for the section shown in figure? 40 mm 100 mm 100 mm…

A: Given data, To find the (a)elastic section modulus (b)Shape factor

Concept explainers

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.

Question

Please help me with this one. Please use the second photo as reference.

Subject: Strength of materials

Topic: Torsion

3- a steel pope ller shaft is to foan&mit 45mw
a4 3 H2' without exceeding a sfearing sfress
4 50 Mpa tr tuisting thru more tfan 10
in a lkrgth g o6 diameters. Compute the
po per diameter if G= 83 G Pa.

TORSION
Equations of compatibility – relations between stresses that are compatible with
the deformations.
Equations of equilibrium – relations between the stresses resulting from a study
of the equilibrium between externally applied loads and the internal resisting
forces over an exploratory section.
Torsion Formulas
0 = TL/JG
0- angle of rotation (radians)
T-torque (N-m)
L- length (m)
J- polar moment of inertia (m")
G- modulus of rigidity (N/m)
If we wish to express O in degrees, we multiply the right-hand member by the unit
fraction, 180°/r rad = 57.3° /rad
By replacing the product GO/L by its equivalent value T/J:
T = Tp/J
This is called the torsion formula.
The formula that determines the maximum shearing stress is a more common
form of the torsion formula. It is obtained by replacing p by the radius r of
the shaft:
Max t = Tr/J
1. The stresses must not exceed the shearing proportional limit.
2. The formulas are applicable only to circular shafts, either solid or hollow.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis and procedures for material selection

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
Verify the value of Zx for a W1850 that is tabulated in the dimensions and properties tables in Part 1 of the Manual.
Use an elastic analysis and compute the extra load in the weld (in kips per inch of length) caused by the eccentricity.
A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
The given beam is laterally supported at the ends and at the 1 3 points (points 1, 2, 3, and 4). The concentrated load is a service live load. Use Fy=50 ksi and select a W-shape. Do not check deflections. a. Use LRFD. b. Use ASD.