**Problem Statement:**Select the lightest W section using A36M Steel for a column to support axial compression dead and live loads of 800 kN and 1000 kN respectively. The member, which is to be 4.0 m long and to be fixed top and bottom, has lateral support (pinned) supplied in the weak direction at mid depth as shown.**Diagram Explanation:**The diagram illustrates a vertical column with a bracing mechanism. It shows a W-section steel column fixed at both the top and bottom. The lateral support is depicted as a pinned connection located at the mid-depth of the column, providing stability in the weak direction. The bracing is indicated sideways to emphasize its function of minimizing lateral displacement in the column.

Given, Fy = 36 ksi or 250 MPa DL = 800 kN LL = 1000 kN

= Select the lightest W section using A36M Steel for a column to support axial compression dead and live loads of 800kN and 1000 kN respectively. The member, which is to be 4.0 m long and to be fixed top and bottom, has lateral support (pinned) supplied in the weak direction at mid depth as shown

= Select the lightest W section using A36M Steel for a column to support axial compression dead and live loads of 800kN and 1000 kN respectively. The member, which is to be 4.0 m long and to be fixed top and bottom, has lateral support (pinned) supplied in the weak direction at mid depth as shown

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A portal frame P Q R as shown in figure has a fixed support at P and free end at R. A point load of…

A: For a portal frame PQR as shown below,fixed support at P and free end at Rpoint load of 3 kN is…

Q: If the allowable shear stress is 300 Mpa, determ ine the diameter for the hinge support.

Q: # 3: Analyze the beam 6 kN 1 kN/m 3 KN shown in beam below and draw the bending moment and shear…

A: The loads acting on beam are given . Note According to the company rules i am able to answer first…

Q: steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly…

A: Given:- Span = 4m Simple Supported beam Tensile stress = 35N/mm2 To find:- w, δmax compressive

Q: 2. Design the compression member in Problem 1 using W14 and A-50 steel. Use ASD with PDL= 990 KN AND…

A: Given, W14 , A50 steel PDL = 990 kN PLL = 680 kN

Q: Situation 4: A W530 x 92 simply supported beam has a length of 12 m. The beam supports a super…

A: NOTE : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: A plate girder is composed of the following elements: Web plate: 900 mm depth x 10 mm thickness Two…

Q: Q2 Identify the zero-force members and the forces in members EF and EG using method of sections in…

Q: An I-section shown in Fig. is simply supported over a span of 12 m. If the maximum permissible…

Q: quarter points. The maximum live load deflection must not exceed L/240 1 Q3- The beam shown in…

A: To Find Select a W shape section that can resist live load. Given concentrated load = 90 kN = 20.232…

Q: the rectangular beam given in figure below has been designed for flexure; design the necessary shear…

A: It is required to determine the factored load. wu=1.2DL+1.6LL=1.240+1.625=88 kNm It is required to…

Q: A W21x50 structural steel wide-flange section is used as a simply supported beam with a span length…

Q: Determine the maximum uniform load w that the beam can carry using A-36 steel. The lateral supports…

Q: A steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly…

A: Consider the free body diagram;

Q: An A36 W 12 x 65 column section is 8 m long, pinned at each end and has an additional support in the…

Q: PA plate girder is composed of the following elements: Web plate: 900 mm depth x 10 mm thickness Two…

Q: An inverted T RC column is proposed. Its cross-section and reinforcement is shown in the sketch…

Q: A) Define the following terms: - (choose 5 only) Curb, collector streets, sight distance,…

A: Note- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: A W14x68 column has a length of 28-ft and it is pinned at the top and fixed at the bottom. Using a…

A: A W14×68 column A=20 in2 rx=6.01 in ry=2.46 in Length, L=28 ft=336 in Pinned at top and fixed at…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Net power output =280 MW. Pressure ratio of the gas turbine cycle =11 Air enters the compressor at…

Q: A portal frame P Q R as shown in figure has a fixed support at P and free end at R. A point load of…

A: For a portal frame PQR as shown below,fixed support at P and free end at Rpoint load of 3 kN is…

Q: stress Oy in ksi). Both ctor of safety of FS = N te shear failure. De - See table to comp

Q: calculate the reactions at the supports A and B for the following beam with uniformity distributed…

A: Free body diagram of given beam:-

Q: QUESTION 1: Determine the force acting on member GC. A 5 kN 3 m 2 kN 5 kN -2 m- B -2 m- C 2 m- 5 kN…

A: Given data

Q: A W310 X 117 of Grade 60 steel is used as a compression member. It is 8.5m long, pinned at each end,…

A: Given, DL = 800 kN LL = 1420 kN

Q: 4. If the tank is held so that the top is 3.0m below the surface of water, what is the force on the…

A: Width of tank = 1.2m Let length of tank = 1m d(depth of water inside the rank from normal level of…

Q: 3-3 A rectangular section with width b=200mm and depth h=450mm is reinforc with 4 16 of HRB400. The…

A: Width (b) = 200 mmDepth (h) = 450 mmReinforcement of concrete = 4 -16 diameter HRB400Design Moment…

Q: The given frame is unbraced, and bending is about the x axis of each member. The axial service loads…

A: Dead load (PD) = 908 KNLive load (PL) = 1816 KNYield strength (Fy) = 350 MPa ≈ 50.76 ksiMoment of…

Q: Design for the circular section the maximum uniformly distributed load

A: Given:- Allowable bending stress, σall=14 ksi=2016000 lb/ft2Allowable shearing stress, τall=8…

Q: Member BC is an A992 W12x40 and is bend about its strong axis. Take L = 20-feet, Pu 90 kips, and wu…

A: Member BC is an A992 and is bent about its strong axis. All joints are pinned.To determine:moment…

Q: Five planks (4@ 40 x 40 mm and 1@ 40 x 380 mm), are joined together to form the l-section shown.…

Q: Determine the force acting on members.

A: Step 1:For the given problem lets first eliminate the zero force member from the given truss,by…

Q: A compression member is built up from a W14x90 and a W10x49, both of A992 steel. a. Compute rx and…

A: We need to first obtain the Moment of inertia about X and Y axis We can determine the moment of…

Q: Determine the roller support reaction components at B and the fixed support components at D for the…

A: Composite beam : A structural member is made up of two or more distinct materials that have been…

Q: A W12 x 65 of A572 steel (E= 350 MPa and Fy= 450 MPa) is used as a compression member. It is 8 m…

A: ASD design method Length of column (L) = 8 mDead load (PD) = 800 KNLive load (PL) = 1420 KNFrom AISC…

Q: 17.4 A W410 X 100 structural steel wide-flange section is used as a horizontal lower chord member of…

A: We have to deterime the maximum and minimum combined stresses due to the direct axial load and the…

Q: An RC column, built with M25 grade concrete, of square cross-section (500 x 500 mm²) is subjected to…

A: Given Data M25 grade concrete Column size = 500 mm × 500 mm Factored load (Pu) = 937.5 KN Used…

Q: See the image below. A hot-rolled I-beam section has yield strength fy = 300 MPa, ultimate strength…

Q: For simply supported beam 2m 1 KN 3 KN/m 5 KN/m 4m 1m 2m 2m 2m V=0 M-0 1) Find the reactios 2) Draw…

Q: An inverted T RC column is proposed. Its cross-section and reinforcement is shown in the sketch…

Question

100%

**Problem Statement:**

Select the lightest W section using A36M Steel for a column to support axial compression dead and live loads of 800 kN and 1000 kN respectively. The member, which is to be 4.0 m long and to be fixed top and bottom, has lateral support (pinned) supplied in the weak direction at mid depth as shown.

**Diagram Explanation:**

The diagram illustrates a vertical column with a bracing mechanism. It shows a W-section steel column fixed at both the top and bottom. The lateral support is depicted as a pinned connection located at the mid-depth of the column, providing stability in the weak direction. The bracing is indicated sideways to emphasize its function of minimizing lateral displacement in the column.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Trending now

This is a popular solution!

Step by step

Solved in 8 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the area of cross section of a single angle discontinuous strut is 30cm2 and allowable working stress corresponding to its slenderness ratio is 625 kg/cm², the safe load carrying capacity of the member is (a) 10 tonnes (b)12 tonnes (c) 15 tonnes (d) 18 tonnes
Question 2: A compression member is subjected to service load of DL-180 KN and LL-335KN. The member is 6 m long and fixed at A and pinned at B. Use 992M steel F, = 345 N/mm² Select W shape, make two complete attempts. 6m B A
Solve it.
4. A beam-column made of a W200x71 ASTM A992 steel, Class 1 section, is subject to factored axial compression C=1300KN and a factored transverse point load, P=100 kN, located as shown in the diagram below. Pt creates bending about the strong axis. The member has a length, L=4.0m, it is pinned at its ends and is part of an unbraced frame. Lateral torsional buckling is prevented thus does not apply. Determine whether or not this member is adequate as a beam column. 2L/3 L/3
Question 17
answer should be on the choices
The column (W12x72) has a total height of 6m and designated as A36. It is supported at both ends by a fixed support and carry an axial compressive load. Using the recommended design effective length factors, determine the maximum stress carried by this column
The floor system shown below supports a uniform dead load of 100 lb/ft² and a uniform live load of 40 lb/ft?. Draw the loads with magnitudes on the following structural members: а) BI b) В2 с) ВЗ d) B4 e) Gl f) G2 g) G4 6 @ 7' = 42' C4 G1 B3 B2 2 @ 15' = 30' G4 G3 G2 BT 5 @ 6' = 30' 42' 36' For the same floor plan shown above and assuming the same floor loads and that the building consists of four floors, determine the following: a) The dead load on column Cl in the first floor. b) The live load on column C2 in the second floor. Consider live load reduction. c) The sum of the dead plus live loads on column C3 in the third floor. Consider live load reduction. OT
Question 6: Determine the LRFD design compressive strength for the shown built-up compression member composed of 2 channel (MC) sections welded to a plate. The effective buckling length of the member (KL=21 ft 2 in). Use steel with F, = 42 ksi. PL를X 12 KL = 21 A 2 in F, = 42 ksi Hint: Use parallel axis theorem to find moment of inertia about x and y axis. MC 13 x 50
A bracket of length 1.5m is rigidly attached to the simply-supported beam at its end. The beam is subjected to the combined effect of M,, M, and compressive force P caused by the factored loads as shown. There are lateral supports only at the ends. The member is made of HE300A section and steel grade is S275 (Fy-275MPA, Fu= 430 MPa). The loads acting are determined from LRFD combinations. Determine whether the member can safely carry the applied loads. Multiply first-order moment diagrams by a factor of 1.2 to account for second-order effects. No need to check shear limit state. You do not need to additionally consider the beam self-weight. E Use the following simple expression to calculate the value of L:: L, = T*rts 0.7*Fy y P = 400kN 1.5 m F = 150kN 2 т 4 т X: Lateral support НЕЗ00А
Find the value of internal force member and state if it is in Tension or Compression
please help