Select the lightest C section that will safely support the service tensile loads PD= 65 k and PL= 50k. The member is to be 14 ft long and is assumed to have two lines of holes for 3/4-in O bolts in the web. Assume that there are at least three holes in each line 3 in on center. Use A36 steel. (Ans. C8 × 18.75 LRFD and ASD)

Select the lightest C section that will safely support the service tensile loads PD= 65 k and PL= 50k. The member is to be 14 ft long and is assumed to have two lines of holes for 3/4-in O bolts in the web. Assume that there are at least three holes in each line 3 in on center. Use A36 steel. (Ans. C8 × 18.75 LRFD and ASD)

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.2.5P

See similar textbooks

Similar questions

1.A tension member is 25 mm thick plate as shown. The bolts are 20 mm. diameter high-strength bolts. The steel is A36. Compute the following: 130 mm 25 mm 0 0 a) The design strength for LFRD. b) The allowable strength for ASD. 25 mm CIVIL ENGINEERING STEEL DESIGN
The tension member is a PL 12 x 6. It is connected to a 38-inch-thick gusset plate with 7/8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16" Use: Consider deformation at the bolt hole 3" PL ... PL ½x 6 12" 24" 24" 12" a. What is the minimum spacing as per AISC code provisions Round your answer to 3 decimal places.
Compute the design strength (øPn) of the double angle tension member shown below for the following limit states: • tensile yielding in the gross section • tensile rupture in the net section • block shear rupture Identify the controlling limit state. Note: • The angles conform to ASTM A36 • LLBB = long legs back-to-back PL I" 11 (6) 7/B DIA. BOLTS z" 3" 2" -2L6x4x%2 LL BB
Read the situation carefully and answer the problem with complete, clear, and correct solution. A PL 3/8 x 7 tension member is connected with three 1-inch-diameter bolts, as shown in Figure P3.2-1. The steel is A36 Fy-36ksi, Fu=58ksi. Assume that Ae = An and compute the following. a. The design strength for LRFD. b. The allowable strength for ASD. PL 3 x 7 FIGURE P3.2-1 "There is no elevator to success, you have to take the stairs." - Zig Ziglar God bless. Ⓒ
3.6-4 Select an S shape for the tension member shown in Figure P3.6-4. The member shown will be connected between two plates with eight %-in. diameter bolts. The service dead load is 216 kips, the service live load is 25 kips, and the length is 22 ft. Use A36 steel. a. Use LRFD. b. Use ASD. O O O O FIGURE P3.6-4
A double-angle tension member, 2L 3 x 2 x 4 LLBB, of A36 steel is subjected to a dead load of 12 kips and a live load of 36 kips. It is connected to a gusset plate with one-line of 3/4-inch-diameter bolts through the long legs. Does this member have enough strength? Assume that A₂ = 0.85An. Ae Use LRFD. Use ASD. 1 2 IL Section CIVIL ENGINEERING STEEL DECIGN
A C8 x 11.5 is connected to a gusset plate with 7/8 inch diameter bolts as shown in Figure P3.2-3. The steel is A572 Grade 50. If the member is subjected to a dead load and live load only, what is the total service load capacity if the live to dead load ratio is 3? Assume that Ae=0.85An. Use LRFD and ASD.
Steel design Subject
4. An UPE 300 is to be used as a tension member and it is bolted to a 10mm thick gusset plate with bearing type 8-M20 8.8 bolts as shown in the figure below. a. Check all spacing and edge distance requirements. b. Compute the allowable tensile strength of the channel UPE 300. Don't consider shear strength of the bolts and bearing strength of the bolt holes. [all dimensions are in mm] Material both for gusset plate and UPE 300: S275 F-275N/mm² Fu=430N/mm² UPE 300 Ag = 5660 mm² tw 9.5 mm x = 28.9 mm 70 160 70 + 10mm thick gusset plate +50+ 80 -80-80-50 o +50+80 -80 80-50 UPE 300
At the connection at point C, 4 M20 bolts are used to connect the U150x75x6.5x10 profile with the gusset plate, tb = 10 mm. The quality of U profile steel and gusset plate is BJ41. Bolt quality is A490M with shear plane on the non-threaded part. a) Check the bolt clearance requirements in the direction of the force. b) Check that the shear strength of the bolt is sufficient to withstand the factored load SUBC. c) Determine the distance between the bolts, s, so that the bearing strength of the connected plates is sufficient to withstand the factored load SUBC. Baut M20 - S, BC U150x75x6,5x10 Pelat buhul, t = 10 mm Kolom WF 300x300x10x15 (satuan dalam mm) 81
Determine the allowable tensile force P which can be appllied to the plates shown. The AISC specifications A36 steel and 20 mm diameter A325 bolts placed in standard holes with threads excluded from the shear plane are used in a bearing in a bearing type connection. Fy = 248 MPa, Fu = 400 MPa, Fv = 206.9 MPa and Fp = 1.5 Fu. P P CIVIZ 12mm 250 mm ENGINEERING - STEEL DESIGN 12mm P P
A Channel C6x13 is used as a tension member. The holes are for 5/8 inch in diameter of bolts. Using A36 steel with Fy=36 ksi and Fu=58 ksi. The gross area of C6x13 is 3.81 in? and Assume U =0.85 Using LRFD what is the design strength based on Tensile Rupture/Fracture 4 @ 2" a 1 1/2 Ob 3" Oc 1 1/2 " I d e C6 x 13 Round your answer to 3 decimal places.