Answered: Select a lightest W14 section to…

Select a lightest W14 section to support the axial compression loads Pd=660kN and Pl= 880 kN if KL = 4.2m and A572 Grade 50 steel is used. Use NSCP 2015 Specs. Check using LRFD and ASD methods..

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q1: Compute elastic section modulus Sx, plastic section modulus Zx and Shape Factor for the section…

A: moment of inertia about Neutral Axis N.A I= 0375×11312+2…

Q: A W 14 x 142 is used as a column having length of 9 m long. It is hinged at the upper end and fixed…

Q: 10-3 Shearing Stress and Deflection in Composite Beams 423 1014. A rectangular section 150 mm wide…

Q: 2. A W14 x 99 steel section has a span of 9 m and has a lateral support 1/3 point. Fy = 345 MPa.…

Q: Calculate the magnitude of a uniformly distributed load (in addition to the beam's) which will cause…

A: Given : Width of web, Bw = 250 mm Width of bottom, Bb = 500 mm Width of flange, Bf = 750 mm…

Q: A reinforced concrete cantilever beam is shown below. The beam cross section is a rectangle, 12…

A: Given data Concrete weight (wt) = 150 pcf Find maximum bending moment due to self weight of beam.…

Q: Compute the compressive strength of a WT12 x81 of A992 steel. The effective length with respect to…

A: Find, compute the flexural buckling strength for the x-axis (the axis of no symmetry):…

Q: Determine the available compressive strength (p.P) of a composite column with the length of 25 t.…

A: Available compressive strength of the column= PN= Ac(0.85 fc')+Asfy fc'=5000 psi Ac=…

Q: P H

A: We have to using ASD method, and resting on a concrete pedestal that 450*400mm. and find the check…

Q: Design an interior span slab of a concrete floor system with the following description: Span = 10 m…

A: The slab is an important element in the structure for carrying floor load and another live load that…

Q: Compute the compressive strength of a C15 x 50 of A36 steel. The effective lengths with respect to…

A: For the compressive strength, we have to calculate both LFRD and ASD flexural strength.

Q: (4) 30 t W 27x84 A992 steel (a) If the beam is not laterally braced 4 Mn= ? 6) If the beam is…

Q: = By using LRFD method, select a W10 shape for column GH shown in figure for the following data: Wa…

A: Solution: Given: Dl = 200 lb/ft LL = 1000 lb/ft steel A572 grade 50 L= 50 ft h = 30 ft

Q: Determining the spacing of a pair of connecting screws (connectors) between the slab and the steel…

Q: DETERMINE THE MOMENT IF INERTIA OF THE BUILT UP SECTION ABOUT THE INDICATED X. AXIS. The thickness…

Q: Select a lightest W14 section to support the axial compression loads Pd = 660kN and Pl = 880 kN if…

A: Answer: We are given Axial Compression load Dead Load Pd = 660 KN Live Load Pl = 880 KN Effective…

Q: USE NSCP 2015 A W460X177 is used as a compression member with one end fixed and the other end fixed…

A: Given values: Section used: W 460*177 Length, L =3657 mm One end fixed and other end fixed against…

Q: For the composite shaft shown, the total twisting angle is the sum of the twisting angles of steel…

A: False The shafts are bonded together as a composite bar so they will have strain compatibility. As…

Q: An HSS10 × 8 × 3/16 is used as a compression member with one end pinned and the other end fixed…

A: The given data is shown below: HSS10×8×316Length=3.65mA500 Grade BFy=318 MPa

Q: The rectangular RC members under uniform load, the cross section of the beam is b×h = 250×500 mm. A…

A: The compression strength means the material or structure's ability to resist loads that tend to…

Q: 2. Select the most economical (lightest) W sections of A572 Gr. 50 steel. The beam is braced at ends…

A: A572 Gr. 50 steelLb = 15'WDL = 3 klfWLL = 1 klf

Q: A3. A composite beam and deck system made up of W360x72 at 1000mm o.c. is to span 8m. The deck when…

A: Given data: Section W360 x 72 @ 1000mm fck = 25 MPa Density of concrete = 24kN/m3 Slab thickness =…

Q: Q2. Design the required tensile and compression rebars for the cross section shown below. Mu= 288…

A: for given cross section given b=250mm D=500mm MU=288KN-M FC=20 MPA FY=300MPA

Q: An exterior column shown should be more of an axial member than a flexural member if the…

A: For A-50 steel fy = 345 MPa & E = 200 x 106 N/mm2 For column Ix = 687 x 106 mm4 rx = 146…

Q: Select the lightest W360

A: Dead load is a constant load that does not change with respect to time but live load is not constant…

Q: Determine the Safe load P for LRFD and ASD to be applied in the structure shown, such that a…

Q: AW14 x 74 of A992 steel has a length of 20 feet and pinned ends. Compute the design compressive…

A: Given ; W14 X 74 , A992 steel L = 20 feet and pinned ends TO FInd : Design compressive strength for…

Q: ompute the nominal compressive rength (kips) of a C12X30 with a ngth of 12 feet. The member ends e…

A: C12x30 L=12ft Nominal compressive strength =?

Q: Select the best hot-rolled W-section for the given column

A: Calculating the factored loadfactored load=1.2Dead Load+1.6Live Load…

Q: For this Problem, kindly refer to our Textbook, Steel Design Fifth Edition by William T. Segui. For…

A: Solution: Given: load = 85 kips Direct shear: V=855=17 kips Find the centroid location: x=3×35=1.8…

Q: Q2. Given: f'c= 28MPa fy= 420MPA Section: rectangle: b= h= 500mm Loads: Pu= 3833kN Mu= 300kN.m…

A: We will solve this question as per IS456 CODE AS PER THIS CODE, THE relation between ultimate moment…

Q: AW14 x 53 of Grade 70 steel is used as a compression member. It is 30 feet long, pinned at the top…

Q: An HSS10x10x3/16 is used as a compression member with one end pinned and the other end fixed against…

A: The section HSS with one end pinned and the other end fixed against rotation but free to translate.…

Q: For the welded angle, determine the maximum tensile strength. Assume A992 grade steel. 6" 4" -Pu -L5…

Q: (1) The out-plane stability formula of beam-columns recommended in the design code is as following:…

A: The values of these factors are as follows:

Q: A W18 97 with Fy = 414 MPa is used as a compression member. The x length is 4m. Compute the nominal…

Q: An A36 W14X605 simply supported steel beam with span “L” carries a concentrated service liveload…

A: Given, A36 W14X605 simply supported steel beam with span “L” carries a concentrated service live…

Q: Q4/ Give reason PLLA and PDLA are more common used for load-bearing applications?

A: The PLLA and PDLA are known as Poly-L-lactic acid and poly-D-lactic acid. These polymers are blends…

Q: Describe about the flow nets and why are they used?

A: Flow net is a graphical representation of the water flow through the soil mass. It consists of…

Q: The T-section shown is subjected to a design ultimate moment of M = 180kN.m. Find the require area…

A: Solution: Given: fc = 30 MPa fy = 450 MPa bf = 400 mm hf = 100 mm bw = 200 mm d = 350 mm

Concept explainers

Introduction to Steel Design

The area of steel design is majorly concerned with the structural engineering domain, which is a specialization of civil engineering. Steel design is often known as structural steel design, whose primary concern is to design steel structures. The primary structure involves the designing and construction of frames using structural steel as the material. Residential buildings, houses, bridges, complexes, tall buildings, industrial warehouses, aircraft frames, frames of ships, and stadiums are some of the examples of structures that use steel framing.

Question

Select a lightest W14 section to support the axial compression loads Pd=660kN and Pl= 880 KN if KL = 4.2m and A572 Grade 50 steel is
used. Use NSCP 2015 Specs. Check using LRFD and ASD methods..

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: We are given

VIEW

Step 2: Calculate required Area

VIEW

Step 3: Selecting the required section :

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 87 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

AW14 x 43 column in a braced frame has a yield stress of 50 ksi and a height of 10 ft. The column is pinned at the top and bottom and has no intermediate bracing. Determine the available strength of the column considering the critical stress for flexural buckling. From AISC Manual Table 1-1, the properties of a W14 x 43 are: A = 12.6 in^2 tw = 0.305 in bf/2tf = 7.54 h/tw = 37.4 rx = 5.82 in ry = 1.89 in Ix = 428 in4 ly = 45.2 in4 G= 11,200 ksi J = 1.05 in^4 Cw=1950 in^6 What is the nominal axial strength considering flexural buckling stress of the column section (in kips). O 310 O 468 O 447 O 375 O 420 O 436 O 517 O 280
If you can't solve this question just skip it but don't say this is an assignment question.
DETERMINE THE MOMENT OF INERTIA OF THE BUILT-UP SECTION ABOUT THE INDICATED X. AXIS. The thickness of the stem in problem 2 is 1.5". Please show clear and complete solution in tabulated form. Thank you
Using Fy=50 ksi select the lightest W14 Section available for service column loads PD=120 and PL=220 where KL=10 ft. (Recheck your solution)
Solve it
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES - STEEL DESIGN
A reinforced concrete cantilever beam is shown below. The beam cross section is a rectangle, 12 inches deep by 18 inches wide. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Concrete tensile strength: f't = 400 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Beam is not exposed to weather or in contact with soil. Determine if the beam will crack under its own weight, if its self-weight is 250lb/ft. 10 ft -18" BEAM SECTION beam will crack beam will not crack unknown, not enough information to calculate
A compression member AB (HE 400 B) is pinned at both ends and braced in the weak direction as shown in the figure. Material and geometrical properties are given below. For the given loading and ASD load combination (PG+Pq=3500 KN), determine whether the section is satisfactory or not. Material: 5355 F355 MPa F 510 MPa E= 200000 MPa Section properties (HE 400 B): A: 19780 mm² d: 400 mm h: 298 mm t: 13.5 mm. tr: 24 mm b: 300 mm i,: 170.8 mm İy: 74 mm B X -BRACING IN THE WEAKDIRECTION
An A36 W14X605 simply supported steel beam with span “L” carries a concentrated service liveload “PLL” at midspan. The beam is laterally supported at supports and its midspan. Consider its beam selfweight to be its service deadload, “w” (use ASEP steel manual for selfweight, w and other section properties). In checking section's compactness, calculate the upper limit for non-compact web category? Express your answer in 2 decimal places.
plss, i need the answer immediately!
A3. A composite beam and deck system made up of W360x72 at 1000mm o.c. is to span 8m. The deck when cast is to be 100mm thick concrete (25MPA). The shear studs to be used have an ultimate stress capacity of 415MPA and will have a diameter of 16mm. Assuming 100% connection and that the system is shored during casting determine the ultimate moment of the composite W360.