scillator are 2 m/s and 4 m/st.
Q: What is this accurate reading?
A: The scale in the illustration is also known as a triple beam balance scale. It is commonly used to…
Q: Calculations: Use the force diagrams to create an equation for the Net Force on each mass:…
A: Introduction: The net force on a body is equal to the mass of the body and the acceleration of the…
Q: (d) 6N 8 kg (c) 5N (a) 10 N (b) 9 N 4 kg 8 N 10 N 8N 5 kg 6N 5 kg
A:
Q: Measure the slope of the line of best fit. Since D = kgd, the slope will equal Va so multiply by Va…
A:
Q: 2 part question.
A: Part (1 of 2) Basic Details The force acting on the electron depends on the charge of the electron,…
Q: 8 9 70 1 2 3 4 5 6 7 8 Wooden plank - length (CLOSEUP) 9
A: 6.3 12.2 Length of wooden box "l"= 12.2 cm Width of wooden box "b"= 6.3 cm Formula used :…
Q: Please help ASAP
A: To find : the value on the y axis represented by point P
Q: Review | Constants | Periodic Table (Figure 1) shows a snapshot graph at t = 0 s of two waves…
A: The objective of the question is to determine the correct snapshot graph showing the string at t = 3…
Q: What is the length of the object in cm?
A: Required : The length of the object.
Q: A box of mass m-3,0 kg on a frictionless plane inclined at angle O,-30° is connected via a cord of…
A: The correct option is b. With θ1=30 and θ2=60 we get a = 0.45 m/s2
Q: Calculate the average acceleration using the pormula. ă = in which we started at ,- Ő at to -0. Mass…
A:
Q: 10. The axis of this post should be located within a cylindrical zone of .015" at MMC with respect…
A: Geometric control or Geometric dimensioning and tolerance uses symbolic language, that especially…
Q: Stress/MPa O 1200 3000 800 600 400 % 该 t 0.5 15 Stra/ O Figure 1: Stress vs strain plot for a…
A: Given: Stress vs strain
Q: Instructions 50 cm 10 cm 8.0 A R = 1.0 x 10-3
A: According to Faraday law Induced emf is the rate of change of magnetic flux. Induced current=…
Q: For A= 4î + ĵ − 3k, B = -4î + ĵ + 5k, and C= 5ĵ − 2k, find C · ( A−B )
A: Given : A= 4î + ĵ − 3k B = -4î + ĵ + 5k C = 5ĵ − 2k
Q: How was 3.15 derived as the Vf of the ball in the provided solution.
A:
Q: b. Explain why the x-component of the total electric field is zero at any point on the y-axis.
A: The formula to calculate the magnitude of the electric field due to any point charge is given by…
Q: middle hic che relationship between these numbers? Low ect of increasing the angle on acceleration?…
A: If the angle of the inclination increases, then the acceleration of the car descending the slope…
Q: At what rate is heat being generated in the 8.7 N resistor on the right? Answer in units of W.
A:
Step by step
Solved in 2 steps with 2 images
- 83184kg = 199.7 mg ball-bearing with arcum ference of 26.1 mm wegs 200mg Circumference of a circle = 2nr)? what is the density of the steel in g/cm³ (u of sphere = 4133 A steel 200mg Ⓡ Deng S (mm) Density = D = Di2g 3 D= masse lume S 062994 cm³ 0.66800267 v=4/7| (4:16mm)³_290-4mm 3 mm³ cm Convert + Tr = 4 tr ² 3 0 C = 2115 C = R 211 2994mm² (1 cm )3 26.1mm = 4.16mm 2 x 3.14 10 mm)³ mg-> conuert 200mg 1000g DRAA 0.21. Use the data of three trials with the launcher in a horizontal position to determine average, standard deviation and uncertainty of both time and range. Table 1: Trial Time t_(s) Range Ax_(m) 1 0.2049 0.963 0.2114 0.972 3. 0.2083 1.009 Average 0.2082 0.981 Standard deviation Uncertainty Check: Measure the height of ncher H with your ruler: H = 21.4 cm calculate the theoretical time of flight: Is the above value in good agreement with the average time from table 1? Explain. 2. Using the data in Table 1 calculate the initial speed vo= Axevezse/toveurs Initial speed Xe= (units:If p/m is .9c,what is v in terms of c?