rpm diesel engine and operating under moderate shock load. The pump will operate at 800 rpm. The recommended small sheave diameter is 6 inches. Calculate the following: a)The large sheave

Q: For a pump designation 1-x3-10 provided by the manufacture, find out the appropriate options for…

A:

Q: Data for the Tesla Model 3 shown in figure 1 are given in the table below. Figure 1: Tesla Model 3…

A:

Q: Define drive head

A: Given Data⇒ drive head Problem statement⇒ Problem says Define drive head

Q: 11) Steering wheel of truck have larger diameter than that of a passenger car. Why?

A: Steering wheel of truck have much larger diameter than that of a passenger car:

Q: Please create a simple ping pong ball launcher where there is a mechanism for the trigger. And…

A: We have to given a initial launch angle and a launch initial velocity. And according to the initial…

Q: 1. What is the power ratio of a pump and its 1/4 scale model if the ratio of the heads is 5:1?…

A: Given data:- scale model = 1/4 the ratio of the heads =5:1 To find:-the power ratio of a pump

Q: In raising the pole for the position shown, the tension T in the cable must supply a moment about A…

A:

Q: A pump is driven by an electric motor through a open type flat belt drive. Motor pulley diameter…

A:

Q: In case of vane pumps Centripetal force causes vanes to come out of rotor slot. Select one: O True O…

A: A rotary vane pump is a positive displacement pump that consists of vanes mounted on a rotor that…

Q: A single cylinder engine is used to drive an irrigation pump. The set-up has the following data:…

A: The diameter of the pump pulley: 305.5556 mm

Q: Read through the following chronological instructions. Choose the correct figure that best matches…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: Shown in the Figure is the complete pump performance chart for a 3x4-10 centrifugal pump at 1750…

A: 3×4-10 centrifugal pump speed =  1750 rpm,  pump must deliver at least  = 200 gal/min of water…

Q: Briefly describe pump selection using characteristic curves provided by the pump manufacturer.

A: Pump selection using characteristic curves provided by the pump manufacturer

Q: 1) Draw a simple sketch of your regulator design 2) Draw a simple sketch of the spring

A:

Q: b) A gasoline engine is specified to be 4-stroke and four-cylinder. It has a bore of 80 mm and a…

A:

Q: A bucket elevator has a head pulley diameter of 14 inches. There are 260 buckets having a size of 4…

A:

Q: a) Define the "force exerted by air pressure" in a pneumatic cylinder? b) Differentiate double…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 2.State the operation principle of positive displacement pump according to the following figure

A: Given Positive displacement pump To find Operation principle

Q: 7. A mobile application with the pump driven directly from the engine delivers 12 gal/min at a…

A: Introduction: Pumps are used to move fluid from one location to another in order to convert…

Q: 1) The working face of ordinary flat key is 1 A. Side B. Upper top surface C. Bottom surface D. End…

A: (1)

Q: For the case of a perfectly plastic

A: Given: The maximum reduction in cross-sectional area per pass (R) of a cold wire drawing process is:…

Q: A rotating slurry pump is to be driven by a 50hp, 2400 rpm diesel engine and operating under…

A: Note:- As per the honor code we can answer upto three sub-parts. Please, repost question to get…

Q: P) Draw the kinematic diagram of the excavator arm and calculate the mobility of the mechanism

A: Draw diagram of arm and mark Number of links and binary joints Number of links (L) = 12 Number of…

Q: What are the characteristics of oil pumps for boilers and engine generators? Select all that apply.…

A: Oil is sent to the engine-driven fuel pumps through booster pumps, which pass it via heaters and…

Q: A multi-cylinder engine is to run at a constant load with an average speed of 600 rpm. The magnitude…

A:

Q: A bucket elevator has a head pulley diameter of 14 inches. There are 260 buckets having a size of 4…

A: GivenDiameter of head pulley=14inches=355mm=0.35mNo. of…

Q: If we assume that a given pump requires 7.50 ft of NPSH when operating at 3500 rpm, what would be…

A: According to the given data (NPSH)1= 9.5 ft  N1= 3500rpm N2 =2850rpm We need to find  (NPSH)2

Q: he crank radius of a single-cylinder IC engine is 60 mm and the diameter of the cylinder is 80 mm.…

A: Given:radius of crank, r=60 mmdiameter of cylinder, d=80 mm

Q: A car in idle mode shows 700rev/min on the rev counter,the rev speed in angular velocity on the…

A: Angular velocityω or Ω of an object is defined as the change of angular position of a rotating…

Q: s of di amo er velocity of ensity of the air under these « owing relation DW

A: CD = 24Rep 1+0.15 Rep0.687----- (1)WhereRep = ρg vg - vp dpμ ----- (2)vp = 0vg = 10 m/secρg = 900…

Q: convert 15 rpm to spm

A: To convert revolutions per minute (RPM) to strokes per minute (spm), it is very important to know…

Q: Data for the Tesla Model 3 shown in figure 1 are given in the table below. Figure 1: Tesla Model 3…

A: