rope around the post?

Q: If I had one singular hinge joint, which total different direction could it provide a force in?

A: The hinge joint can rotate and proves zero restriction about the hinge point, thus moment reaction…

Q: Why should the Beams be braced properly along their sides?

A: The bracing is mainly classified into three types  1) Plane bracing 2) Torsional bracing, 3) U frame…

Q: Truss members can change their length due to a change in temperature. True or false?

A: In truss members, there is no change in length. But due to changes in temperature stress is build up…

Q: What is the class of fit of a ½-20 UNF-2B thread?

A: The united thread series is classified into coarse threads, fine threads and extra fine threads. The…

Q: Refer to drawing 21A044, How many full threads will the fine tapped hole contain at minimum depth…

A: A standard thread form and series, along with allowances, tolerances, and designations, for screw…

Q: 2) For a bolted tension member with a lap splice as shown, what are all the limiting tension…

A: Given data, A single strip butt joint is given in the figure. n= No o rivets = 4 To show, all the…

Q: What happens when the boards are bonded together?

A: When the boards are bonded together with an adhesive material, the mechanical interlocking mechanism…

Q: If the pitch of a thread is 1/18 inch, how many threads are needed for the threaded section of a…

A:

Q: just to clarifay is the shaft stainless steel? or the tool making the threads on the shaft

A: It is the shaft which is made up of stainless steel.

Q: Draw the Mohr Circle and mark important points for a rod under pure tensile load & torsion

A:

Q: Refer to drawing 21A044, How many full threads will the extra fine tapped hole contain? (Disregard…

A: In Engineering Drawing, the tapped hole with full threads is denoted in the form of given…

Q: Chapter 8. The formula for fixed fasteners is: t1 + t2 = H - For H = F + t1 + t2 OF-H or F = H + t1-…

A:

Q: What is the cantilevered beam?

A: Cantilever beam- It’s a rigid structure that is made to bear the load applied to its axis. A…

Q: QUESTION: Suppose a bolted tension used in a doube-D ring configuration is properly preloaded. The…

A: given; ⇒spring constant for the bolte (k1)=7.8MN/m⇒spring constant for the member…

Q: What causes the localized buckling of the beam's flanges?

A: To find: The causes of localized buckling of the beam's flange Buckling:  It is defined as the…

Q: What happens when the member is confined?

A: Confined member: If a member is confined then it means it is fixed to a position.

Q: If the length of a column is doubled, the critical load becomes?

A: Given Data⇒ Length of column=L If L=2L Critical load(P1)=?

Q: When facing, the compound rest maybe set 30° (to the cross-slide. If the compound rest is fed in…

A: Draw the diagram of the cross-slide and compound rest.

Q: Which of the following is not a factor in specifying bolts? Select one: A. DIAMETER B. RADIUS C.…

A: Given :- Which of the following is not a factor in specifying bolts? Select one: A. DIAMETER B.…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.