RODS AC AND BC ARE USED TO SUSPEND THE 100 KN WEIGHT. IF EACH ROD IS MADE OF A MATERIAL FOR WHICH THE AVERAGE NORMAL STRESS CANNOT EXCEED 200 MPa, DETERMINE THE MINIMUM REQUIRED DIAMETER OF EACH ROD TO THE NEAREST mm.

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods as shown. The…

A:

Q: Determine the stress produced in cylindrical rod of having diameter 2 mm when Tensile load of 44 KN…

A: Introduction : In this question we are provided with value of tensile load and cross section…

Q: A load of 1950N is raised at the end of a steel wire. The minimum diameter of the wire so that…

A: Given data :- Load  = 1950 N Stress = 100 N/mm2 Calculate the minimum diameter of the wire

Q: A solid shaft has to transmit 50 kW of power at a speed of 1910 RPM, Ignore any possible bending of…

A:

Q: A wire cable was was used to suspend a 500 pound support beam. The orginal length was 12 feet. The…

A: Original length, L=12' Stretched length, L'=12.01' Therefore,  change in length,x=12.01'-12'=0.01'

Q: 500 Ib 12 in. P(x,y) 159 mm 600 kN 0 mm 100 mm 150 mm 50 mm 150 nim 3 in. 6 in. 150 mm

A:

Q: The following shaft consists of a 3.50 m long steel shaft and a 2.00 m long aluminum tube. The steel…

A:

Q: hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400kN. Determine…

A:

Q: A hollow steel tube with inside diameter of 100mm is carrying a tensile load of 400kN. Determine the…

A: Steel tube is given with, External Diameter of 115mm Internal Diameter of 100mm  Carrying a tensile…

Q: A closely coiled helical spring of mean diameter 140 mm is made up of 12 mm diameter steel wire.…

A: GivenDiameter of helical spring D=140 mmRadius R=70 mmDiameter of steel wire which is used in spring…

Q: Q.6 A solid shaft is subjected to a bending moment of 500 Nm and a torque of 700 Nm. Calculate the…

A: given Bending moment M=500 NmTorque T=700 Nmpermissible normal stressσb=100 MPa

Q: 4. The beam shown supports the load shown, determine max flexural stress developed and 200mm the max…

A:

Q: Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A:

Q: A solid 11 mm diameter shaft is subjected to an axial load of P-33 kN and a torque of Tacting as…

A: Note: Hi! Thank you for the question as per the honour code, we’ll answer the first question since…

Q: A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank…

A: Given data, The outside diameter of the tank, d = 180mm Wall thickness t, = 13mm Pressure in the…

Q: Consider a solid circular shaft fixed at one end and free at the other end with a concentrated…

A:

Q: The maximum stress generated in the rope of diameter 25 mm passing over a pulley of diameter 400 mm.…

A: Diameter of the rope D=25 mm,Diameter of the pulley d=400 mm,Modulus of elasticity of the rope E=1.5…

Q: A 1000 kg homogeneous bar AB is suspended from two cables AC and BD, each with a cross-section area…

A: Given -  A 1000 kg homogeneous bar AB suspended from two cables AC and BD. Cross section area =…

Q: Determine the maximum bending stress (in MPa, numerical value only) of the beam shown belovw with…

A:

Q: Find maximum shear stress in the wall?

A: Given, Cylindrical tank inner radius,r= 14 m Thickness,t= 60 mm Gauge pressure,P= 3 MPa Find maximum…

Q: Answers: 0x = Txy Op2 = i i i MPa MPa MPa

A:

Q: a.)Determine the required gap (δ) so that the rails just touch one another when the temperature is…

A:

Q: 1a) Figure Q1a shows two tubes made of the same material which are riveted together by 50 rivets of…

A:

Q: Jor 6 m 5 kN/m -250 mm 20 mm-

A: Determine the maximum tensile stress in the following beam:

Q: 10 lb-ft 50 lb-ft 70 lb-ft (1) (2) 30 lb-ft (3) B

A: Diameter of shaft, ∅=0.86inThere are several torques applied on shaft

Q: Q2/ the structure shown below, support from fix at the left , the max normal at bronze =200 MPA,…

A:

Q: The compound shaft has a uniform cross-sectional area with the given length of each segment. Using…

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.