Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 9 mm in diameter. Assume a = 600 mm, b = 300 mm, h = 400 mm, P = 875 N, and 0 = 55°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A D Answers: (a) Orod= (b) Tpin B = (c) Tpin A = (1) a i H i B b MPa MPa MPa

Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 9 mm in diameter. Assume a = 600 mm, b = 300 mm, h = 400 mm, P = 875 N, and 0 = 55°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A D Answers: (a) Orod= (b) Tpin B = (c) Tpin A = (1) a i H i B b MPa MPa MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

L = 0.3m A = 20 x 6 mm E= 70 GPa allowable stress = 120 MPa 0.6 m 0.4 m 0.2 m Rigid bar D C W 0.5m 40 x 6 mm 50 GPa wable stress = 80 MPa 16 mm dia. bolt with allowable s 6 mm 80 MPa in bearing and 60 MPa The rigid bar A,B,C,D shown in figure is connected to the ground by a hinge at B and to Magnesium bar at A, Aluminum bar at C. the properties of the bars are shown on the figure. all the connections are using 16 mm bolts in single shear. Determine the maximum safe load W that can be applied. Determine the final position of point D.
A solid steel bar of diameter di = 1.4 in. is enclosed by a steel tube of outer diameter d3 = 2.25 in. and inner diameter d2 = 1.9 in. (see the figure). Both bar and tube are held rigidly by a support at end A and joined securely to a rigid plate at end B. The composite bar, which has length L = 26 in., is twisted by a torque T = 5,100 lb-in. acting on the end plate. Tube A Bar End plate (a) Determine the maximum shear stresses T1 and T2 in the bar and tube, respectively. Round your answers to the nearest whole number. T1 = psi T2 = psi (b) Determine the angle of rotation (in degrees) of the end plate, assuming that the shear modulus of the steel is G = 11.5 × 10° psi. Round your answer to three decimal places. (c) Determine the torsional stiffness kT of the composite bar. Round your answer to the nearest whole. [Hint: Use equations below to find the torques in the bar and tube.] T = T GIp, + G2IP, kT = k-in.
please solve step by step and correctly
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=33P=33 kipskips is applied to the assembly at A, two loads of Q=30Q=30 kipskips are applied at B, and two loads of R=35R=35 kipskips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 1717 ksiksi. The normal stress magnitude in steel rod (2) must be limited to 3030 ksiksi. The normal stress magnitude in brass rod (3) must be limited to 2121 ksiksi. Determine the minimum diameter required for each of the three rods.
The pin-ended wrought-iron pipe shown in the figure below has outer diameter D, inside diameter d, and length L; it supports an eccentric load P based on a safety factor of n. Find the largest allowable eccentricity e. Given: D = 190 mm, d = 170 mm, L = 3.5 m, P = 430 kN, n = 1.4, E = 190 GPa, 0yp = 210 MPa.
Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 6 mm in diameter. Assume a = 600 mm, b = 250 mm, h = 425 mm, P = 900 N, and 0 = 55°. Determine the the shear stress in pin B. Express your answer in MPa rounded to the nearest hundredths. Answer: Blank 1 D ... (1) B a Blank 1 Add your answer
Neat solution
Uniform AB brass rod has a rectangular vertical cross section, fixed with support and pin as shown in the figure. Both ends of the rod are free in the vertical direction but rotation in the horizontal direction is prevented. a) Find the b / d ratios at the safe boundaries for the horizontal and vertical axes?b) What would be the safety factor if P = 1.8 kN, L = 7m, d = 60mm and E = 150GPa?
At the end of a production line at Danfoss, a 40 kg box of thermostats with speed 3 m/s is colliding with a 10 kg box at rest. What is the common speed of the two boxes right after impact?