Rigid bar ABC is supported by pin-connected axial member (1) and by a pin connection at C, as shown in the figure. A 4,700-lb concentrated load is applied to the rigid bar at A. Member (1) is a 3.50-in.-wide by 1.00-in.-thick rectangular bar made of steel with a yield strength of Gy = 33,000 psi. The pin at C has an ultimate shear strength of 6 = 69,000 psi. Assume P = 4,700 lb, a = 29 in, b= 44 in., c = 20 in., and d = 35 in. (a) Determine the axial force in member (1) (positive if in tension and negative if in compression). (b) Determine the factor of safety in member (1) with respect to its yield strength. (c) Determine the magnitude of the resultant reaction force acting at pin C. (d) If a minimum factor of safety of FS = 3.1 with respect to the ultimate shear strength is required, determine the minimum diameter that may be used for the pin at C.

Rigid bar ABC is supported by pin-connected axial member (1) and by a pin connection at C, as shown in the figure. A 4,700-lb concentrated load is applied to the rigid bar at A. Member (1) is a 3.50-in.-wide by 1.00-in.-thick rectangular bar made of steel with a yield strength of Gy = 33,000 psi. The pin at C has an ultimate shear strength of 6 = 69,000 psi. Assume P = 4,700 lb, a = 29 in, b= 44 in., c = 20 in., and d = 35 in. (a) Determine the axial force in member (1) (positive if in tension and negative if in compression). (b) Determine the factor of safety in member (1) with respect to its yield strength. (c) Determine the magnitude of the resultant reaction force acting at pin C. (d) If a minimum factor of safety of FS = 3.1 with respect to the ultimate shear strength is required, determine the minimum diameter that may be used for the pin at C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rigid beam BC shown in Figure is supported by rods (1) and (2) that have cross-sectional areas of 175 mm2 and 300 mm2, respectively. For a uniformly distributed load of w = 15 kN/m, determine the normal stress in each rod. Assume L = 3 m and a = 1.8 m.
Q8(): For the truss shown in the Figure, if the diameter of pins at A and G are 3 in and2 in, respectively. Both stresses in A and 70 kips 50 kips A 4ft В 4# C 4ft are double shear. Determine the shear stresses in 9 ft pins at A and G and the stresses members AG; AF member GF if their diameter is 4 in and in.
Rigid bar ABC (see figure) is supported by axial bar BD and a pin connection at C. A load P-6000 N is applied at A. Member BD is a 20 mm wide by 9 mm thick rectangular cross-section bar. The pin at C has an allowable shear stress of tallowable = 115 MPa. The overall dimensions of the assembly are a = 110 mm, b= 190 mm, c 50 mm and d= 13 %3D mm. (a) Determine the normal stress in member BD. (b) Determine the required pin diameter at C. B A
Q8(): For the truss shown in the Figure, if the diameter of pins at A and G are 3 in and 2 in, respectively. Both stresses in A and 70 kips 50 kips 4 ft B 4 ft are double shear. Determine the shear stresses in pins at A and G and the stresses in 9 ft members AG; AF member GF if their diameter is 4 and in.
Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the shear stress occurring in the point.
a vertical hollow circular shaft of aluminum shown below fixed at the top has a load P equal to 150KN exerted on its lower end. neglecting self weight, determine the minimum outer diameter d2 and maximum inner diameter d1 if a) the allowable stress = 50MPa b)the allowable elongation =2mm the thickness of the material is one tenth of the outer diameter and young modulus E = 80000MPA
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=33P=33 kipskips is applied to the assembly at A, two loads of Q=30Q=30 kipskips are applied at B, and two loads of R=35R=35 kipskips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 1717 ksiksi. The normal stress magnitude in steel rod (2) must be limited to 3030 ksiksi. The normal stress magnitude in brass rod (3) must be limited to 2121 ksiksi. Determine the minimum diameter required for each of the three rods.
A homogenous bar AC with negligible mass is supported by a pin at A and cable BC, carried a load of 20 kN as shown in the figure. Determine the pin diameter at A if the allowable shearing stress is 80 MPa. (double shear) 3 m. 4 m. C 20 kN B.
Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 6 mm in diameter. Assume a = 600 mm, b = 250 mm, h = 425 mm, P = 900 N, and 0 = 55°. Determine the the shear stress in pin B. Express your answer in MPa rounded to the nearest hundredths. Answer: Blank 1 D ... (1) B a Blank 1 Add your answer
A steel torsion bar AB with diameter d = 34 mm, and ductile material of tensile yield strength Sy = 276 MPa is attached to a rigid arm at A, supported by a bearing at C, and fixed at B, as the picture shows. At the right end of the arm is mounted the wheel on which the vertical force P acts from the ground and which passes through the center of the wheel. If bearing C acts as a simple support and the effect of transverse shear due to P is negligible, determine the maximum force P (in kN) that can be applied to the wheel. Consider a factor of safety n = 2.5. Use the maximum energy of distortion failure criterion and do the analysis on bar AB (torsion bar) in the section where the bearing is.
A uniform concrete slab of total weight W is to be attached, as shown in the figure, to two rods whose lower ends are on the same level. Determine the ratio of the areas of the rods so that the slab will remain level. Figure P-215 Steel E - 29 x 10 psi Aluminum E - 10 x 10 psi L- 4 ft L-6R Total Weight = w 3 ft 6 ft The value of the load P at the aluminum 0.33 W b. 0.67 W с. W d. none of the above The ratio between the internal reactions of the aluminum and the steel 2.03 b. 0.49 c. 0.67 d. none of the above The ratio between area of steel and area of the aluminun 0.867 b. 0.409 c. 0.258 d. none of these If the value of W is limited to 1500 lb, which of the statements is true? The maximum load the steel can carry is greater than of the aluminum The maximum load the aluminum can carry is greater than of the stell The sum of loads at the steel and the aluminum is twice the value of steel The deformation developed at the steel is greater than that of aluminum If the cross-sectional area…
PROBLEM 2. The carrier system in the figure consists of the AB rigid beam and two aluminum bars and a steel bar connected to it. After the assembly is created at 20 °C without causing any prestresses, calculate the stresses on the bars if the temperature is increased to 80 C. Steel A-36 A =160 mm? 3,5m 10 kN/m 3 m 3m 2 m 2014-T6 Aluminum A =200 mm E A,