rget superheat answer Actual superheat answer

Q: 1. If the Pressure Entering the Condenser is 15 KPa. What is The Temperature at the oxit of the…

A:

Q: Example 21.6. Find the maximum torque that can be safely applied to a shaft of 200 mm diameter if…

A:

Q: Briefly define heat and work from the thermodynamics perspective and give TWO examples of…

A:

Q: A polytropic process of air from 150 psia, 300°F, and 1 ft³ occurs to p₂ = 20 psia in accordance…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 5500 kg of steam is produced per hour at a pressure of 7.6 bar in a boiler with dryness fraction…

A: GIVEN DATA - Mass M=5500kg/hr BOILER PRESSURE =7.6bar DRYNESS FRACTION X=0.98 FEED WATER TEMPRATURE…

Q: 12 kg of air per minute is delivered by a centrifugal air compressor. The inlet and m3 and kg outlet…

A:

Q: Superheated steam enters an insulated turbine at 4000 kPa and 500°C and leaves as saturated steam at…

A: Given:P1= 4000 kPaT1=500oCP2=kPa, and here it's given that it's saturated steam so, x2(dyness…

Q: Which of the following gasifiers has the Lowest thermal output?

A: Answer is Downdraft

Q: What is the length of the finned section of pipe in this baseboard hot waterheating system?

A: Find    Calculate the length of the finned section of the pipe

Q: Section 2: Numerical Response Q3 : If the flow into a wind turbine is 10 m/s, and the flow far…

A: Given:The upstream velocity of flow, The downstream velocity of flow,

Q: Refrigeration topic. Please help with the problem. Thanks

A: The research field of refrigeration is a very versatile and in modern era, there is tremendous…

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: 3-22. The stress-strain diagram for a polyester resin is given in the figure. If the rigid beam is…

A: 3-22 Given, The diameter of the strut AB, ds=12 mm=0.012 m The diameter of the post CD, dp=40…

Q: Carbon dioxide (CO₂) fills a closed, rigid tank fitted with a paddle wheel, initially at 80°F, 20…

A:

Q: A power transmission shaft (torsional shaft) is to be produced using carbon fibre epoxy composites.…

A: given; for composite shaft power transmission(P)=?

Q: Q2) Water is being heated in a closed insulated pan stirred by a paddle wheel. During the process…

A: Given data: -  The heat transfer is Q = 5000 J. The work done is W = 1.5 kJ. The initial internal…

Q: Define Constant Specific Heats (Approximate Analysis)

A: In constant specific heat assumption, the specific heat is assumed to be constant at some average…

Q: Steam enters a convergent-divergent nozzle at pressure of 22 bar and temperature of 300°C. the exit…

A: From steam tables at pressure of 22 bar, saturation temperature is 217.24oC. As the temperature of…

Q: What is the maximum gas flow rate for a nozzle size?

A: GIVEN; What is the maximum gas flow rate for a nozzle size?

Q: 7. Water at 10°C is flowing from point A to point B through the fabricated section shown below at…

A:

Q: 21. A 5V3350 drive belt is connected to a normal torque squirrel-cage electric motor operating at…

A:

Q: Which hotspot on the lever below acts as the Effort?

A: This question is based on the concept of lever.

Q: As shown in the figure below, a cylinder fitted with a piston is filled with 400 lb of saturated…

A: Given DataThe amount of the saturated ammonia filled in the piston is: The temperature of the…

Q: Question 4 Given the ultimate/gravimetric analysis of coal as follows: C-81.95%, H2=4.63%6,…

A:

Q: What is the minimum gas flow rate for a nozzle size?

A: Given: What is the minimum gas flow rate for a nozzle size?

Q: For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment…

A:

Q: Determine the distance s to which the 90-kg painter can climb without causing the 4-m ladder to slip…

A: Given Data mass of painter, m=90 kg=90×9.81=882.9 N Length of the ladder, l=4 m Distance of ladder…

Q: What is a standpipe?

A:

Q: 25.25 Use the following differential equations to compute the velocity and position of a soccer ball…

A: The differential equations of motion for the soccer ball are given as: dydt=vdvdt=-g-cdmvv The…

Q: How can we ensure boiler operation safety?

A: To Explain : The boiler operation safety.

Q: 5.5-23 A beam ABC with an overhang from B to C supports a uniform load of 3 kN/m throughout its…

A: Data given - Total length L= 6m Uniform load = 3KN/m Moment of interia about z axis = 210cm^4…

Q: Measures that can be taken to improve the boiler efficiency ?

A: Requirements to increase the efficiency of the boiler :

Q: Discuss boiler feed water properties, treatment and sampling procedure.

A:

Q: Write the differences between the boiler mountings and accessories

A: Boiler mountings are used in boilers primarily for safety purposes. The main function of mountings…

Q: 12) Zeroth law of thermodynamics (a) deals with conversion of mass and energy (b) deals with…

A: