Rewrite each of the following measurements in their clear- est and most appropriate forms: (i) x = 3.323± 1.4mm (ii) t = 1, 234, 567± 54, 321s (iii) A= 5.33 × 10-7 ± 3.21 × 10-9m (iv) r = 0.000, 000, 538±0.000, 000, 03mm

Q: Question 25 A change in the mode field diameter (MFD) results in a change in: O signal velocity O…

A:

Q: 3- Which of the following signals is periodic and calculate the period of them: a) x[n] = e b) x[n]…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: The Energy of the signal 10 e-stu(t) in the frequency band [0] Hz is

A: To find the energy of the signal in the frequency band Hz, we can use Parseval's theorem, which…

Q: Apply Input : 10sin(wt) . Plot the output graph and express. Calculate the RMS. R1= 2kΩ

A:

Q: loov C 18.8 PF R 2171-43~ 30.45H Find, IT, Ic, IR, IL

A: Given that: The circuit is shown below. Find: IT, IR, IL, and IC.

Q: Given the information provided in the figure below, determine ß, Vcc, RB. 20 μA RB Vcc •2.7 kΩ VCE =…

A: Note   When BE and CB junction of BJT is reverse biased= Cut off Region When BE forward and CB…

Q: MAX VOLTAGE = 2.32V MIN = -2V PK- PK = 4.40V RMS = 1.29V Period = 930 x 10-6 s (930 us)…

A: Given data: Vpeak-peak=4.4 VT=930×10-6 sMax Voltage=2.32 V   The waveform is given as:

Q: If the transit has an interval focusing telescope, this indicates that a. the additive constant is…

A: Transit having an interval-focusing telescope is used for the measurement of the stadia system.  The…

Q: In the figure, ɛ = 12.0 V, the time constant is 500us, and Imax = 200 mA. What is L? S R A. 500 µH…

A:

Q: 7. If the time constant (tau) is .000033 s, and R = %3D 3.3 kOhm, then C = ? %3D .01 nF .01 uF .01 F…

A: Time constant of RC circuit is RC Where R is the resistance  And C is the capacitance.

Q: X[n]=2cos(2n)  what is the period?

A: Given function is  X[n]=2cos(2n) Although for a discrete function condition for periodicity  is…

Q: Sketch the resultant wave form when the following two pulses meet. (Assume the meeting point…

A: Generally, pulses are the representation of the signal shows its nature, amplitude, frequency, etc.

Q: LS RKN In 32A Un 240/415V- 30mA 0.15 CE IEC61008 LS Industrial Systems Test monthly 1/3/5/N 246 N…

A: The given picture is of LS RKN, 32 A RCBO switch which is used as Residual current circuit breaker…

Q: Identify which measurement this oscilloscope time difference reading is useful for. Osilloscope-XSC1…

A: This is oscilloscope waveform.  Difference between waveform?

Q: The number of passive elements in the second order transient circuits is O 1 O 4 O 3 02

A: About 2 nd order transient circuits.

Q: Calculate circular convolution of the numbers 2091 and 6324.

A: Given : Note : Here we have considered the given numbers are with commas, such as the given numbers…

Q: . What happens when the angle alpha is zero + V(+) itt) 82 10.663mF To. 26.53 mH V(t)=155.56 Cos…

A: Given that  V(t) = 155.56 cos(377t+ 23.8°) v R = 8 ohms  C= 0.443 mF L = 26.53 mH

Q: Find V, the magnitude, A direclion of unknowh urrenti through 10, 52 4 20 istance resistors. 1. 15A4…

A:

Photoconductive Cell

Photoconductive cells are light-sensitive resistors in which resistance is inversely proportionated to light intensity when illuminated. These devices consist of a thin single-crystal or polycrystalline film of composite semiconductor materials. Cadmium sulfide (CdS) is used to make the most commercially available photoconductive particles which are sensitive to light in the visible spectrum. Other less commonly used substances respond to infrared light, but not to the visible spectrum. Such substances are lead sulfide (PbS), lead selenide (PbSe), and lead telluride (PbTe), and so on.