Please answer problem 3-26 Air at 40 F (5 C) db and 35 F (2 C) wb is mixed with warm air at 100 F (38 C) db and 77 F(25 C) wb in the ratio of 2000 cfm cool air to 1000 cfm warm air. Find the resulting humidityratio and enthalpy using psychrometric Chart la on the basis of volume flow rates.3-25. SIS OL VOlow fatcs.Rework Problem 3-25, using Chart la, with the mixture condition computed on the basis of themass flow rates rather than volume flow rates. What is the percent error in the mixture enthalpyand humidity ratios?3-26.The

Answered: Image /qna-images/answer/7add893c-650a-47da-af73-22ad248b23c2.jpg

Answered: Rework Problem 3-25, using Chart la,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please draw the figure. Thank you so much.An engine flywheel and a clutch plate are both connected to a transmission shaft. Let the moment of inertia of the flywheel be I1 and its angular velocity ω1, and let the moment of inertia of the clutch plate be I2 and its angular velocity is ω2. The two discs have then been combined by forces which are applied at their axes of rotation so as not to cause any torque. The discs then reached a common final angular velocity after rotational collision. Find the expression for the final angular velocity.
Now consider the figure shown below. N CG -A tip In the above figure the block is just on the verge of tipping: W and N act through point A and thus exert zero torque about point A. The incline angle, Otip, is the incline angle beyond which the block will tip, since increasing the angle beyond Otip will move the CG beyond where there is a point of support below it, as in the previous figure. It is not difficult to show, using some geometry and trigonometry, that Otip is given by Orip = tan' (w / h) (1) Equation (1) agrees with our intuition: If the block is short and wide (h small, w large) the block will be more difficult to tip (Otip is large) and if the block is tall and narrow (h large, w small) the block will be easier to tip (0tip is small). It is now not difficult to see why the automotive industry defines a safety factor describing how easily a vehicle will rollover as (roughly) vehicle width / vehicle height. The larger this safety factor is, the more resistant the vehicle is…
Show all steps and solutions . Solve both and no copied answers please include both in full answer with full solution and steps
Short answer please
Draw using tip to tail method please show steps 4-3. Draw a free-body diagram of member BD in Figure P4-3. 10 40 mm 60 mm mm В 50 N 15 mm 15 mm

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Rework Problem 3-25, using Chart la, with the mixture condition computed on the basis of the mass flow rates rather than volume flow rates. What is the percent error in the mixture enthalpy and humidity ratios?