Review Replace the loading by an equivalent resultant force and couple moment acting at point 0. Suppose that Wi = 9 kN/m and w2 = 5 kN/m (Figure 1) Part A Determine the equivalent resultant force. Express your answer to three significant figures and include the appropriate units. Enter positive value if the force is upward and negative value if the force is downward. HA ? Figure <) 1 of 1> FR =19.86 Kn 9 The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. Submit Previous Answers Request Answer w, Part B 1.5 m- -0.75 m- 0.75 m Determine the couple moment. Express your answer to three significant figures and include the appropriate units. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. P Pearson

Q: (b) The steel shaft has a diameter of 40 mm and is fixed at its ends A and B as shown in Figure…

A: For solution refer below images.

Q: need help with part b i solved a prior

A: ◆ The mean effective pressure: 562.94 kPa. ◆ The indicated power developed by the engine is 4.10 kW.…

Q: Answer by true or false for the following       Specific heat is a measurement of the ability of the…

A: The specific heat of a substance is defined as the amount of heat to increase the temperature of the…

Q: The center rod CD of the assembly is heated from T = 30 °C to T = 210 °C using electrical resistance…

A:

Q: Write the mathematical form of Newton's second law of motion.

A: Newton’s second law of motion states that the resultant of actual force is always equal to effect or…

Q: 4. In what standard plates can we index the following. Solve using sil label each values. a. gear of…

A: we have to determine the plate size for manufacturing the given items by simple indexing

Q: Double acting cylinder cannot be used as a single acting cylinder. Select one: O True O False

A: Single Acting cylinder as it were expands by weight from a pump and after that withdraws by the…

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A: If A= 0.375 inch, B=0.923 inch, C=1.0992 inches,find G.

Q: Question 1 The helical steel extension spring has a diameter of 2 inch, wire diameter of 0.1 inch,…

A: Given: diameter of the spring: D=2 inch diameter of the wire: d=0.1 inch for steel shear modulus:…

Q: The distributed load of w = (-2x² + 4x + 16) lb/ft acts on the beam as shown(Figure 1). Part A…

A:

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to…

A:

Q: Draw chalk diagram of all sections

A: To draw section views

Q: The steel box wrench (E=29,000ksi, v=0.32) is loaded with a 40-lb horizontal force and a 25-lb…

A:

Q: Tapered gibs are adjusted by screws spaced out along the length of the gib. Select one: O True O…

A: Tapered gibs

Q: 4. In what standard plates can we index the following. Solve using simple indexing anda label each…

A: we have to determine the plates required for simple indexing

Q: of the table) and free to move if a force is applied. A force is applied on it as the arrow…

A:

Q: The diameter of the bolt is .500 inches. Force

A: given:diameter of the bolt d=0.500inforce F= 750pound

Q: A 70 kg skier that moves from rest at A is shown in Figure Q2. Suppose friction can be neglected…

A: Given:m=70 kgθ=30°θ=40°Height AB=12mTo find:-1) Velocity VB2) The istance S

Q: If a force doubled, impulse will triple. True or false

A:

Q: Q.1) Knowing that the tension in cable BA is 570 N, determine the moment about O. Neglect the…

A:

Q: now please answer question 2 and 3 please

A: This question is based on the concept material science. As per the guidelines we are subjected to…

Q: -As shown in the Figure 2, please to draw the axial force diagram of the roa. 20 kN Figure 2 10 kN…

A:

Q: Mr. Ahmed wants to replace his car door, for this purpose he has selected cast iron. Select one:…

A: IT IS FALSE.

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: Answer in 4-10

A: Given: →h1=3387.31 KJ/Kg→h2'=3074.5 KJ/Kg→h3=3457.04 KJ/Kg→h4'=3109.82 KJ/Kg→h5'=2384.82…

Q: What is the meaning of + S.F, -S.F, +B.M and ?- B.M

A: There are sign convention for shear force and bending moment.  The shear force at a cross-section is…

Q: Interpret the significance of the letters shown in the illustration

A: Instruction given at tail of the welding symbol is "See detail A".Here detail A will have the…

Q: Given the force in spring AD (150N), final length of spring EC (0.8m), spring constant k = 9 N/cm,…

A: As per give condition,  For solution refer below images.

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.