Review Activity 13-2 BRANAON BRANDOW MCCAILM For ench of the aritten descriptioms below, sketch a fentrure comtral frame that muntiches the description given. 6. The profile of this surface should be within a .010" zone with respect to datums A, B, and C between X and Y. 1 This feature must be flat within 003". O.003 .010 ABC X本 2. The cross-sectional shape of this feature must be round within a radial tolerance zone of .002". 7. The surface elements of this cylinder must be straight within .002". .002 |-l0.02 3. FIM reading of this surface should be within .005", measured at any location along the axis, with respect to datum A. 8. This surface must be perpendicular to datum C within .005". .005 C 4 This hole should he located within a cvlindrical 9 The runout of this culindriga

Q: What about Mohr's circle?

A: In the previous question, Given: The diameter of shaft, d = 20 mm = 0.02 m The maximum bending…

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: Why is it important to determine the slopes and displacements?

A: Slope – when ever any load is applied on the beam due to its elastic properties it bend in very…

Q: What is the part’s over all length?_______________________ 6. Whatisthe part’s over all…

A: considering the detailed drawing of an object to find out the answers of the given questions.

Q: What do you mean by vibrations?

A: Vibrations are defined as the to and fro motion of the body, which is periodic about the zero or…

Q: Write short notes on significance of grashoff number.

A: The answer is given below

Q: (a) The U-tube shown in Figure Q3 (a) is rotated about one of its arms at an angular speed of o…

A:

Q: I need answers to problems 4, 5, and 6 pertaining to the print provided.

A: In the given print the length and diameter of the part is to be calculated. Which is mentioned in…

Q: 3

A: intro- defects on any material is cause of failure of material.

Q: Need auxiliary views of this drawing

A: This question is based on the concept of engineering drawing.

Q: What are the Coplanar Loadings?

A: Loadings are said to be coplanar when they all are lying in a plane example :  Plane trusses

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: A 90° elbow shown in Figure 5 (a) is to direct water flow upward at a rate of 50 kg/s. The water is…

A:

Q: (a) Figure Q2(a) shown the nut slides down the cord OA. When it is at the midpoint, its speed is 200…

A: Givenspeed=200mm/sAcceleration=10mm/s2

Q: What is the minimum pressure required to reduce volume of a brass sphere by 0.00003 %?

A: Given:reduction in volume=0.00003%

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: What is external force?

A: Answer : Force - It is an effect which changes or try to change the state of a body.

Q: What are limits or limits of size?

A: This question belongs to Metrology. Metrology is a science of measurement by using different…

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: Write the equation to calculate the work done by an axial force?

A: Work: Work is defined as the multiplication of the axial force on the body and displacement…

Q: 2 Brass expands more than iron when heated. How would the strip look after prolonged exposure to…

A:

Q: The thin plate with four holes as shown in Figure 6 has a mass per unit area of 33 kg/m². The radius…

A:

Q: The possibility to make the required shape from the material is considered during the criteria for…

A: Material to make the desired shape is considered during the criteria of selection. Because during…

Q: QI Define five of the following with sketch. 3- AA2024 4- Rolling 5- Wire drawing 1-Taper turning 2-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: 9. The top view shows a bend radius of the thin metal. Would a bend radius of 1/8" meet the…

A: If the bend radius lies with in the given range then it will meet the requirements. 18"=0.125" The…

Q: Anisotropy in a metal O increases residual stresses. O properties vary with direction. increase the…

A: 1) Anisotropy- it is the property of material in which the meterial properties changes with…

Q: I have three parts that I need answered pertaining to the print provided below.   What material is…

A: To find the material specified for the part in the drawing, refer Title Block of the drawing.

Q: How far from the lens must the film in a camera be, if the lens has a 32.0 mm focal length and is…

A: Given data as per question Object distance(u) =80 cm =800 mm Focal length(f) =32 mm  Here Location…

Q: Is this for number 1 only?

A:

Q: In the hardness test, answer the questions 1- What happens to the sample if its thickness is less…

A: Thickness of the specimen should be at least seven times of the depth of the indentation. It allows…

Q: What are the concentrated forces?

A: Concentrated forces are more a  mathematical idealizations than a realistic. Force applied at a…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.