RESISTIVITY AT 20°C CONDUCTOR ENGLISH (N-cmil)/ft MKS (N-m) 1.72 x 10- 1.77 x 10-8 Annealed Copper Hard-Drawn Copper Aluminum *Note: Use this table if applicable. 10.50 2.83 х 10-8 10.66 17.00 1. An aluminum conductor with a diameter of 0.2in. was badly damaged during a short circuit. It was decided that a hard-drawn copper conductor with the same resistance will be used in its place. What should be the diameter of this copper conductor?

RESISTIVITY AT 20°C CONDUCTOR ENGLISH (N-cmil)/ft MKS (N-m) 1.72 x 10- 1.77 x 10-8 Annealed Copper Hard-Drawn Copper Aluminum *Note: Use this table if applicable. 10.50 2.83 х 10-8 10.66 17.00 1. An aluminum conductor with a diameter of 0.2in. was badly damaged during a short circuit. It was decided that a hard-drawn copper conductor with the same resistance will be used in its place. What should be the diameter of this copper conductor?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Calculate the resistance of a solid round conductor with radius 0.7 mm, resistivity 2.7 x 10-8 2-m and length of wire 54 m. 0.95 O 0.02 0.35 0.66
A 10 AWG copper conductor with Type THW insulation is to rum in free air. What is the maximum ampacity of this conductor if the ambient air temperature is 40 degrees C?
을 A circules ring of 3 turns iis made of Conducting wire. Now same wire The M.F. is bent to form ring of ctuong centre ( I Aome) at centre s B. Then flo M. F. at
Primary EL 600 Volts EP = IL |||| IP = Primary Secondary Secondary EL = EP = 277 Volts IL = IP = Ratio = VA 125 KVA = 1. What size THW copper conductors are needed for the primary conductors? 2. What size THW copper conductors are needed for the secondary conductors? 3. What size Overcurrent protection is needed for the primary conductors?
3. A two conductor main A B, 500 m in length is fed from both ends at 250 volts. Loads of 50 A, 60 A, 40 A and 30 A are tapped at distance of 100 m, 250 m, 350 m and 400 m from end A respectively. If the X- section of conductor be 1 cm and specific resistance of the material of the conductor is 1-7 u 2 cm, determine the minimum consumer voltage. 1245-07 VI
Three 10 AWG, type THW conductors are to be installed between poles on individual insulators. What will the conductor ampacity be?
Compute up to 4 decimal places but only encode your final answers with only 3 decimal digits.
These are laminated steel core containing current-carrying copper wires; and in general if it is the stationary part, it is called as
magnetic conductor and electronic conductor in detail.
Calculate the resistance of a solid round conductor with radius 0.8 mm, resistivity 2.8 x 10-8 Q-m and length of wire 55 m. 0.61 0.77 0.01 0.27
PLEASE HELP ME CHOOSE WHAT CORRECT LETTER OR ANSWER 1. The direction of induced voltage in a conductor can be changed by a. increasing the field strength. b. reversing the field direction. c. increasing conductor length. d. decreasing conductor size. e. reversing meter connections. 2. Direct current can be supplied to a load by a loop of wire rotating through a field with the use of a. slip rings. b. c. brushes. electromagnets. d. commutator. e. conductor. 3. Induced voltage can be increased in magnitude by a. increasing the number of lines cut per second. b. using a commutator. c. using slip rings. d. decreasing conductor length. e. properly applying the left-hand generator rule.
What is the rated amps city per phase for six No. 3 THHN copper current-carrying conductors with two conductors per phase (parallel) and all conductors installed in the same conduit