Resistive Voltage The supply across the terminals of this circuit is 170 V, 50 Hz. An ammeter is connected to the supply. ww000 R L

Q: 1. 500 VA -120/240 -120/240-60HZ 1) Turns ratio (n) 2) Isec 37 I pr.

A: The apparent power, The voltage ratio, 120/240 VThe frequency,

Q: Three 47.1 ohm resistors and three 17.1 H inductors are all in series with a 37 volt battery and a…

A:

Q: Given the zener voltage at 9V and the zener power at 1W, what is the range of allowable values of Iz…

A: Given data, Zener voltage VZ=9 V Zener power Pz=1 W

Q: The conductance of a 9230 resistance is a) 1.08 * 103 mho b) 1.08 * 104 mho c) 1.02 * 103 mho d)…

A: The value of the resistance is given as R=923 Ω. The corresponding value of the conductance (in mho)…

Q: (b) For a configuration as shown in Figure Q1(b), determine the current through 402 resistor, I40n-…

A:

Q: In a resistive load, the current angle

A: In the question, The current angle when load is resistive type.

Q: Q) What should be the value of R such that maxin power tansfer can take place from the rest of th…

A:

Q: When you connect a voltmeter to read a dc voltage   a. polarity is not important b. connect the…

A: In this question,  We need to choose the correct options When you connect a voltmeter to read a dc…

Q: Determine the required peak reverse voltage rating in the following circuit. R₁ 1 ΚΩ www Vs 200 Vpk…

A: Peak Reverse voltage:  Peak reverse or peak inverse voltage is the maximum voltage across the diode…

Q: Calculate average load voltage of the circuit if C=0 and a = 5 and RL= 470 ohms. 中 220V GOHZ DI C R…

A:

Q: 12 V 2 kn 3 kn 4 mA 1 kn 3 kn 2 kn 1o

A: The voltage drop across 2k ohms is determined for the above-shown circuit diagram

Q: Three circuits A, B and C are connected in series across a 200 V supply. The voltage across circuit…

A: We got an Series Circuit of A,B,C with, Supply Voltage = 200 V = 200 Sin (ωt) Voltage across circuit…

Q: In the figure below, the voltage reading of the multimeter (Pr1) will be -5 V if V, 10 V and V, 5 V.…

A:

Q: Question 1 A direct current (DC) of 4A flows into a previously uncharged 20 uF capacitor for 3 ms.…

A: For the given data voltage between the plates are determined as shown below

Q: The maximum power that can be generated by a wind turbine is called Select one: O Cut-in Power O…

A: Rated power is the maximum power that any plant will generate.

Q: Which DMM measurement would you expect based upon the red and black leads in this image? 12 V 8 V 4V…

A:

Q: R1 1 ww- High voltage de supply C Us R2 10W 8 3W

A:

Q: 1. Using Multisim Live, what is the voltage in volts between the open terminals "a" and "b" with…

A: In order to find Thevenin's voltage and Norton's Current the load should be removed from the…

Q: what is the voltage shown by the multimeter

A:

Q: Figure 5 shows a current series feedback amplifier. The sampled current signal is the output…

A:

Q: A dc ammeter has an internal resistances of 0.1 ohm. A shunt of 1.010 milliohm is connected to the…

A:

Q: A 10 Q2 resistor is connected in series to a parallel combination of a 60 resistor and a 20 resistor…

A: Given data, R1=10ohm R2=60ohm R3=20ohm V=220V

Q: Determine the output voltage Vout of the summing amplifier shown in Figure 6 below. 10 K 0.1V o 22 K…

A:

Q: the figure shows 6 batteries connected together the resulted volt of the system 12V 200 A 12V 200 Ah…

A: Given six batteries connected together shown in figure

Q: Using Kirchhoff's Law solve the current in each resistor. 2.5 V R1 680 R3 100 R2 510 M R4 100

A: Given circuit:Asked to find the currents in each resistor using kirchoff's law?

Q: For the circuit shown in the figure below B = 0, R = 10 k2, IVBEI = 0.7 v. Find V1. + 3.7 V Q2 V2 Qs…

A:

Q: When electricity stops flowing because of a break in a circuit, the condition is usually called…

A: Because of a break in a circuit, when electricity stops flowing then this is the condition of open…

Q: Calculate voltage across the load resistor and draw the output voltage waveform in the following…

A:

Q: Two (2) 115 V incandescent lamps A & B are connected in series across a 230 V source. If lamp A is…

A: v= 115 volts  A is rated 75 watts  B is rated 50 watts.

Q: Which of the following statements is false? O The current in a series de circuit is divided up among…

A: Given  The current in a series dc circuit is divided up among the resistances.  In a series dc…

Q: A resistor R is connected in parallel with a 10 ohm inductive reactance. The combination is then…

A: Given data, Resistance is R Inductive reactance XL=10 Ω Capacitive reactance Xc=4 Ω Frequency f = 60…

Q: When the voltage source is turned off in a simple circuit consists of a resistor and an inductor,…

A: Given, When the voltage source is turned off in a simple resistor and inductor (RL) circuit, the…

Q: True or False The resistor R characterizes alternating current circuits

A: The answer is FALSE. RESISTOR R   has same characteristics for both Alternating and direct current.…

Q: In your solution, follow the sequence: Given, unknown, solution, and final answer. BOX your final…

A: Basic problem on ammeter and measurements.

Q: current in R1 in ampere

A:

Q: If the resistance is 2 ohms and reactance is 4 ohms, what is the impedance?

A: Given: Resistance R=2 Ω and reactance XL=4 Ω are connected in series.

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.