Required information Water in a channel is retained by a gate with 10 cm width (into the plane of the figure). The gate is supported by a pin at B and by frictionless contact with the bottom of the channel at A. The gate is outfitted with a prewound torsional spring at B with stiffness k+= 75 N-m/rad. d 30 cm C NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. ces The vertical wall BC is fixed in position. If the gate has negligible weight, determine the amount o the spring must be prewound so that the gate will begin to open when d= 60 cm. (Round the final answer to four decimal places.) The amount o the spring must be prewound is

Required information Water in a channel is retained by a gate with 10 cm width (into the plane of the figure). The gate is supported by a pin at B and by frictionless contact with the bottom of the channel at A. The gate is outfitted with a prewound torsional spring at B with stiffness k+= 75 N-m/rad. d 30 cm C NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. ces The vertical wall BC is fixed in position. If the gate has negligible weight, determine the amount o the spring must be prewound so that the gate will begin to open when d= 60 cm. (Round the final answer to four decimal places.) The amount o the spring must be prewound is

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.9P: A safety valve on the top of a tank containing steam under pressure p has a discharge hole of...

See similar textbooks

Similar questions

A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
The first figure gives spring force Fx versus position x for the spring-block arrangement of the second figure. The scale is set by Fs = 190 N. We release the block at x = 13.0 cm. How much work does the spring do on the block when the block moves from x; = +9.0 cm to (a) x = +5.0 cm, (b) x = -5.0 cm, (c) x = -9.0 cm, and (d) x = -11.0 cm? -x (cm) -2 -1 -F, X* = 0 Block attached to spring F = 0 (a) x positive F, negative F (b) x negative F, positive (c)
Question in pic.
A spring package with two springs and an external force, 200N. The short spring has a loin of 35 mm. Constantly looking for spring for short spring so that total compression is 35 mm (d). Known values: Long spring: Short spring:C=3.98 N/mm Lo=65mmLo=87.4mmF=c·fTotal compression is same for both spring. 200 = (3.98(c1) × 35) + (c₂ × 35) 200 = 139.3 + 35c₂ 200 - 139.3 = 35c₂ 60.7 = 35c₂ c₂ = 60.7/35 Short spring (c₂) = 1.73 N/mm According to my study book, the correct answer is 4.82N/mm What is wrong with the calculating?
A. A car's body has mass 100 slugs. This mass is supported by the car's 4 shock absorbers. The shock absorbers are identical vertical linear springs. Complete a FBD of the car's body (this would not include the car's wheels, axels etc. just the car's body) Each spring is compressed 1.25 inches. Determine the spring "k" value. Answer: 644 lb/inch. Find the compression of each spring if 4 people, each with mass 6 slugs, get into the car, Answer: 1.55" ii. iii.
View In: English v In the below arrangement, all the string and pulleys are massless and the inclined plane is frictionless. At t 0, spring is unstretched and a constant force F = mg starts to act. Find the maximum extension in the spring. (Assume incline to be sufficiently long). Question 11 F=mg Options 8mg 1. O k 4 mg 2. O 5 k 8 mg 3. O 15 k 8mg 4. O 3k
3
I Blackboard @ Texas Tech Univers X Bb MasteringEngineering - Spring 2 × E MasteringEngineering Mastering x Answered: Find the magnitude of X (195) Bryson Tiller - Right My A session.masteringengineering.com/myct/itemView?assignmentProblemlD=12360389&offset=next ABP G KAssignment #3 Problem 2.97 2 of 6 > I Review Suppose that h = 4 m. (Figure 1) Determine the magnitude of the resultant force of the two forces acting on the sign at point A. Express your answer to three significant figures and include the appropriate units. HÀ ? FR = Value Units Submit Request Answer Part B Figure 1 of 1 Determine the coordinate direction angle a of the resultant force of the two forces acting on the sign at point A. Express your answer using three significant figures. 2 m ΑΣφ ? E 2 m vec B F = 350 N Fc= 400 NA F = 400 N Submit Request Answer 2 m 3 m Part C Determine the coordinate direction angle B of the resultant force of the two forces acting on the sign at point A. Express your answer using three…
I want answer of the question clear with resloving and all steps
Solve it correctly please l will rate accordingly.
An undamped spring/mass system, in which m = 8 slugs and the spring constant k = 16 lb/ft has a driving force f(t) = t^pi*t on [0,pi] Extend f(t) into the negative t-axis to obtain an odd function. Find the particular solution ??(?). (Note: f(t) is given as half of the period, p = π.)
Pls solve this question correctly instantly in 5 min i will give u 3 like for sure