! Required information Three loads are connected in parallel to a 1290° Vrms source. Load 1 absorbs 60 KVAR at pf = 0.85 lagging; load 2 absorbs 90kW and 50 KVAR leading; and load 3 absorbs 100 kW at pf = 1. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the current supplied by the source. The current supplied by the source is (1.742 -0.078 ) KA.

! Required information Three loads are connected in parallel to a 1290° Vrms source. Load 1 absorbs 60 KVAR at pf = 0.85 lagging; load 2 absorbs 90kW and 50 KVAR leading; and load 3 absorbs 100 kW at pf = 1. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the current supplied by the source. The current supplied by the source is (1.742 -0.078 ) KA.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
Hi, Help me with this circuit question
A circuit consists of an AC voltage source, a 10-ohm resistor, and a capacitor, all connected in series. The magnitude of the impedance of the capacitor is also 10 ohms. Which of the following is true about the source voltage and the current through the circuit? a. Insufficient information is given. b. The source voltage will lag the current. c. The source voltage will lead the current. d. The source voltage will be in-phase with the current.
In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generators are connected in star with thier star points grounded. The system base is 15 MVA. The transformers all have reactances of 0.04 p.u. on this 15 MVA base. The reactances of all other elements are given in Table 1 (in 2) and the voltage levels are given in Table 2. p.u. G1 p.u. T1 jö Per-Unit Convert all values to p.u. on a 15 MVA base. Xa= p.u. Xc₂= XL = V BABE G1 2 X 9 T3 Figure 1: A section of the distribution system T1 L Table 1: Sequence reactances (2) 3 G1 L G2 0.3 0.59 0.01 4 L 9/10 10 Fault Voltage What is the voltage at bus 3 (in Volts) after the fault has occurred? Vp= V T2 5 T2 34 10/4 Table 2: Voltage bases (kV) G2 4 T3 10/9 | G2 Fault Current A three-phase fault with a fault reactance of 0.01 p.u. occurs at bus 3. Calculate the fault current flowing at the fault point in KA. Ip=-j KA So
X₂=0.1 1 XL +03 Soto X₁ = 0.2 X = 0.1 X = 0.1 Above is the one-line diagram of a simple power system. Each generator is represented by an emf behind the subtransient reactance. All impedances are expressed in per unit on a common base. All resistances and shunt capacitance are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A symmetrical fault occurs at bus 1 through a fault impedance Z, =j0.08 per unit. a) Using Thevenin's Theorem, determine the impedance to the point of fault and the fault current in per unit. b) Find the bus voltages and line currents during the fault. 2 O oto
conductor radius is 0.75cm
60. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the real power. a. 65.3899 b. 392.4372 c. 397.848 d. 588.6559
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
A 400 MVA synchronous machine has H, = 4.6 MJ/MVA and a 1200 MVA machine has H₂=3.0 MJ/MVA. The two machines operate in parallel in a power plant. Find out H relative to a 100 MVA base.
PLEASE ANSWER BOTH QUESTIONS FOR UPVOTES. NO UPVOTE IF ONLY ONE HAS AN ANSWER. PUT ONLY BRIEF EXPLANATIONS ON CHOOSING THE CORRECT ANSWERS. THANK YOU
The total power drawn by the two-impedance load in parallel is 26kW at 0.98 power factor lagging, it is being supplied by a 230-volts AC source. One of the loads (Load 1) takes 16kVA at 0.77 power factor lagging. What is the reactive power of the unknown impedance (Load 2)?
15) Kirchhoff's Voltage Law (KVL) states that A) the product of the phasor voltages around any closed path must equal zero. B) the sum of the phasor voltages around any closed path does not have to equal zero. C) the sum of the phasor voltages around any closed path must equal zero. D) the sum of the phasor voltages around a closed path cannot include "through the air."