Required information The PV diagram shown is for a heat engine that uses 1.370 mol of a diatomic ideal gas as its working substance. In the constant-temperature processes A and C, the gas is in contact with reservoirs at temperatures 373 K and 273 K, respectively. In constant-volume process B, the gas temperature decreases as heat flows into the cold reservoir. In constant-volume process D, the gas temperature increases as heat flows from the hot reservoir. 160 150 A 140 373 к 130 120 B 110 100 273 K C 90 80 0.019 0.024 0.025 0.026 0.02 0.021 0.022 0.023 Volume (m³) Pressure (kPa)

Required information The PV diagram shown is for a heat engine that uses 1.370 mol of a diatomic ideal gas as its working substance. In the constant-temperature processes A and C, the gas is in contact with reservoirs at temperatures 373 K and 273 K, respectively. In constant-volume process B, the gas temperature decreases as heat flows into the cold reservoir. In constant-volume process D, the gas temperature increases as heat flows from the hot reservoir. 160 150 A 140 373 к 130 120 B 110 100 273 K C 90 80 0.019 0.024 0.025 0.026 0.02 0.021 0.022 0.023 Volume (m³) Pressure (kPa)

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Please asap
p (atm) 3. Isotherm Adiabat V (cm³) 1000 2000 3000 Click to see additional instructions The diagram shows a thermodynamic process followed by 101 mg of helium. The pressure of the gas at position 1 is 3.00 atm. How much work is done on the gas and how much heat energy is transferred to or from the gas during each of the three segments? 1-2 2-3 3-1 W (k) Q (k) Data: R= 8.31 J.mol1.K', po = 101.3 kPa Helium: mmol = 0.004 kg.mol1; Cy = 12.5 J.mol1.K1; Cp = 20.8 J.mol1.K1; y = 1.67
A gas undergoes the process shown in the diagram below. During the process AB, the internal energy of the gas decreases and a certain amount of heat Q goes out of the system for the process CA. Use this information to answer the questions below. Select from either positve, negative or zero for each W, Q and ΔU.
The thermodynamic cycle of a heat engine using ideal helium gas is shown in the P-V diagram. The ratio of heat capacities y (also called ratio of specific heats) is the ratio of the heat capacity at constant pressure Cp to the heat capacity at constant volume Cy. For ideal helium gas, y = 1.67. Select the stage that is paired correctly with the process it represents in the P-V diagram. 1-2: adiabatic process O2-3: isochoric process 3-4: isothermal process 4-1: isobaric process p (kPa) 0.8 0.6- 0.4- 0.2 0.0 2 0.2 0.4 0.6 1 0.8 V(m³) 1.0
A monatomic ideal gas is initially in state A. The gas undergoes a transition from state A by the three different processes shown, where process III is isothermal. In which process is energy added to the gas by heating? Explain briefly.
Answer Questions C) D) E)
In an engine, an almost ideal gas is compressed adiabatically to half its volume. In doing so, 2710 J of work is done on the gas. Part A ▼ How much heat flows into or out of the gas? Express your answer with the appropriate units. ? Q = Value Units Submit Request Answer Part B What is the change in internal energy of the gas? Express your answer with the appropriate units. HẢ ? AU = Value Units Submit Request Answer
Question 5 During an sothemal process, 5.0J of heat is removed from an ideal gas. What is the change in internal (thermal) energy of the gas? O 25 J O 25 J O BL9J O 30J
View Policies Current Attempt in Progress Air is compressed in a piston-cylinder assembly from p₁ = 25 lbf/in², T₁ = 500°R, V₁ = 9 ft³ to a final volume of V₂ = 1 ft3 in a process described by pv¹.25 = constant. Assume ideal gas behavior and neglect kinetic and potential energy effects. Using constant specific heats evaluated at T₁, determine the work and the heat transfer, in Btu.
1st and 2nd Law of thermodynamics Worksheet 1. A car engine deliver 8.2 kJ of work per cycle. Its efficiency is 25%. A) How much heat is absorbed and how much heat is exhausted from its fuel combustion? B) The car is now tuned and its efficiency goes to 31%. What are the new values of heat absorbed and heat exhausted? 1 of 3
Q1) There are four main thermodynamic processes that you learned from Unit 3: isobaric, isochoric, isothermal, and adiabatic. For each process below, classify it has one of these processes and then determine the signs of Q (the heat energy that flows into the gas), W (the work done by the gas), and AU (the change in internal energy of the gas). a) A container filled with an ideal gas has been submerged in a large water bath for a long time such that both reach thermal equilibrium. You then slowly compress the gas in the container. Assume the container is not well insulted so heat energy can easily flow back and forth between the water and gas and that the water bath is so large that its temperature does not change very much. b) A container filled with an ideal gas has a well-sealed piston that you put a pin in such that it doesn't move up or down. You then put the container over a burner to heat it up. c) A container filled with an ideal gas has a well-sealed piston that can move up or…
One cubic meter of oxygen at initial pressure of 1 bar and a temperature of 17°C are compressed isentropically to a volume of 0.50m 3. Use the specific heat at constant volume and pressure are 0.919 kJ/kgk and 0.659 kJ/kgK, respectively. determine the: a. The thermodynamic process the problem represents b. the pressure, temperature, and volume after the process c. change in internal energy, change in enthalpy and change in entropy d. work nonflow and heat transferred