Required information Problem 05.038 - Diffuser flow DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air at 80 kPa, 27°C, and 220 m/s enters a diffuser at a rate of 2.5 kg/s and leaves at 42°C. The exit area of the diffuser is 430 cm2. The air is estimated to lose heat at a rate of 18 kJ/s during this process. The gas constant of air is 0.287 kPa-m3/kg-K. The enthalpies are m = 300.19 kJ/kg and h2 = 315.27 kJ/kg. Problem 05.038.a - Diffuser flow Determine the exit velocity of the air. (You must provide an answer before moving on to the next part.) The exit velocity of the air is m/s.

Required information Problem 05.038 - Diffuser flow DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air at 80 kPa, 27°C, and 220 m/s enters a diffuser at a rate of 2.5 kg/s and leaves at 42°C. The exit area of the diffuser is 430 cm2. The air is estimated to lose heat at a rate of 18 kJ/s during this process. The gas constant of air is 0.287 kPa-m3/kg-K. The enthalpies are m = 300.19 kJ/kg and h2 = 315.27 kJ/kg. Problem 05.038.a - Diffuser flow Determine the exit velocity of the air. (You must provide an answer before moving on to the next part.) The exit velocity of the air is m/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Problem 3. Consider a shower that mixes hot and cold saturated liquid water to maintain a steady…

Q: ir at a 800 kPa and 1300 K enters a turbine which has an isentropic efficiency of 90% with a mass…

A: The inlet pressure at turbine is .The inlet temperature is .The efficiency of turbine is .The exit…

Q: Air is compressed in a piston-cylinder assembly. Initially, the pressure and temperature of the air…

A: Change in entropy: Entropy is the ratio of heat transfer (Q) to temperature (T). According to the…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: QUESTION 1 "Water vapor enters a turbine at 6 MPa and 500 C, and leaves the turbine at 100 kPa with…

Q: I. Steam flows steadily into a turbine with a mass flow rate of 20 kg/s at 6 MPa and 600°C with a…

Q: A juice at a rate of 500 kg/h is heated from 60 °C to 115 °C. The juice has a specific heat of 3.85…

A: Introduction In this problem, we will calculate the mass flow rate of steam with the help of the…

Q: 6) Steam enters a turbine at a pressure P-2.0MPA, temperature T1=500°C and enthalpy hi=3062 kJ/kg…

A: Given: P1=2 MPa T1=500oC h1=3062 kJ/kg v1=10 m/s P2=10 kPa h2=2621 kJ/kg v2=50 m/s Q=-5kJ/hr m=4000…

Q: Final Exam Cold air enters the mixing chamber at 85°C and 105 kPa at a rate of 0.55 m /s, while warm…

Q: 8.7 Diffuser A jet flies at an altitude of 10 km, where the pressure is 0.32 bar, and the…

A: To Find:The mass flows into the engine.The pressure increase across the diffuser.Given:The altitude…

Q: Air at a static temperature and pressure of 8°C and 75 kPa respectively enters the intake of an…

A: Air at a static temperature and pressure of T1 = 8°C = 281 K and P1 = 75 kPa respectively enters the…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Given, P1 = 80 kPa = 80000 PaT1 = 27 °C = 300 KV1 = 220 m/sm˙ = 2.5 kg/sT2 = 42 °C = 315 KA2 = 430…

Q: Ammonia and air pass through the heat exchanger. While the ammonia is entering as a superheated…

A: This question have math equation thats why i am using pen paper please rateExplanation:

Q: a desuperheater insulated unit (figure F) converts the inputs into a saturated vapor stream.…

Q: Problem 4 . Steam at a flow rate of 5.21 kg/s enters a turbine at 9000 kPa and 650 °C and leaves at…

Q: Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa,…

Q: A heat exchanger is used to heat 36 kg/hr of air originally at standard conditions (25 °C and 1 atm)…

Q: Carbon dioxide (??=28.2 J/mol⋅K)(Cp=28.2 J/mol⋅K) enters a steady‑state adiabatic compressor at…

Q: The change of enthalpy of air in the cooling tower is 82 kJ/ kg and the mass flow of air is 215 kg/…

A: The change of enthalpy of air in the cooling tower ∆hair =82 kJ/ kg Mass flow of air ma= 215 kg/min…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

You are designing a system to mix fuel and air prior to ignition in an engine. Do you want the flow to be laminar or turbulent? Why?
I. In an air conditioning unit, 3.5 m³/s of air at 27°C dry bulb temperature 50%RH at 100.325 kPa barometric condition enters the Airconditioned Unit (ACU). The leaving condition of the air is 13°C dry bulb and 90% RH. Determine: a. Sensible Heat that was being removed/ added from the ACU? b. Moisture that is being removed/added from the air leaving ACU?
4) Hot combustion gases enter the nozzle of a turbojet engine at 350 kPa, 1007 °C and 95 m/s, and they exit at a pressure 100 kPa. Assuming an isentropic efficiency of 95 percent and treating the combustion gases as air determind a- The exit velocity b- The exit temperature
A reservoir is at effective height of 95m. An irreversible pump is used to pump a mass flow of 4500 kg/s of water from ground level into the reservoir. Consider water as an incompressible liquid with mass density of 1000kg/m . 1) What is the power consumption of pump for an isentropic pump efficiency of 82%? 2) What is the power that can be recovered from a turbine with 93%? (with the same mass flow and height). 3)What is the change in temperature of the pumped water?
ASEM 12/6/2015 Q1/ A stream of warm water is produced in a steady flow mixing process by combining 1.0 kg/s of cool water at 25 °C with 0.8 kg/s of hot water at 75 °C. During mixing, heat is lost to the surroundings at the rate of 30 kJ/s. What is the temperature of the warm water stream? Assume the specific heat of water constant at 4.18 kJ/kg.K.
Task 5 from d to e
2) Argon (ideal gas, Cp=0.5203 kJ/kg.K) at 27 ºC, 85 kPa, and 215 m/s enters a diffuser at a rate of 2 kg/s and leaves at 50 ºC. The exit area of the diffuser is 500 cm2. The gas is estimated to lose heat at a rate of 20 kJ/s during this process. Required: Draw a standard and clear schematic of the problem and label the performance of the schematic. Perform step by step energy and mass analyses, state your assumptions and determine the following:a) The exit velocityb) The inlet areac) The inlet pressure of the Argon
For air properties use online source: https://www.peacesoftware.de/einigewerte/luft_e.html The compressor is operating at steady-state increasing pressure of R-22 refrigerant from 4 bars to 14 bars. Temperature was rising during the process from 12C to 90C. The inlet volumetric flow rate is 1 m3/min and inlet diameter is 0.03m. At the exit the diameter is the same. Heat flow to the surroundings can be neglected. Determine: a.Mass flow rate [kg/s] SHOW AND EXPLAIN ALL STEPS PLEASE thanks