Required information For the C clamp shown, a force is applied at the end of the 0.375 in diameter handle. The screw is a 0.75 in-6 Acme thread (from Figure 8-3), and is 10 in long overall, with a maximum of 8 in possible in the clamping region. The handle and screw are both made from cold-drawn AISI 1006 steel. The coefficients of friction for the screw and the collar are 0.15. The collar, which in this case is the anvil striker's swivel joint, has a friction diameter of 1 in. It is desired that the handle will yield before the screw will fail. where L 3.5 in

Required information For the C clamp shown, a force is applied at the end of the 0.375 in diameter handle. The screw is a 0.75 in-6 Acme thread (from Figure 8-3), and is 10 in long overall, with a maximum of 8 in possible in the clamping region. The handle and screw are both made from cold-drawn AISI 1006 steel. The coefficients of friction for the screw and the collar are 0.15. The collar, which in this case is the anvil striker's swivel joint, has a friction diameter of 1 in. It is desired that the handle will yield before the screw will fail. where L 3.5 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1 please with explanation
Explain please
The bolt is made of a material having an allowable tensile stress of 140.44 MPa and an allowable shearing stress of 55.44 MPa. The bolt will be tightened so that the axial load will be 17 KN. Find the required thickness of the bolt head if the thread is 0.25 mm deep.
IDENTIFY THE ZFM ZERO FORCE MEMBERS
J 6 The cast iron bearing seat in the picture is bolted to the steel beam of the ceiling bracket and supports the gravity load. Use M20 coarse thread ISO class 8.8 bolts with a thickness of 3.4 mm The steel washers are placed under the bolt head and nut. The flange of this bracket is 20 mm thick, the shaft The elastic modulus of the bearing is 135 GPa. (a) Assuming this is a permanent joint and the fasteners are lubricated when assembled, find the required wrench torque. (b) If the gravity load is 15 kN, try to find the load factor n of the design.
3G KOREK docs.google.com/forms Q2: The extension spring shown in the figure has full-twisted loop ends. The material is AISI 1040Q&T 400F0 wire. The spring has 82 coils and is close-wound with a preload of 18 Ibf. (a) Find the closed length of the spring.(b) Find the torsional stress in the spring corresponding to the preload.(c) Estimate the spring rate. (d) What load would cause permanent deformation?(e) What is the spring deflection corresponding to the load found in part d? 0.162 in - in R 글-in R. Option 1
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the allowable tensile strength of the section based on tensile rupture of the net area. Answer: о о lo O o
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P= 20 KN is applied. Sleel E-200 GPa A-400mm L1 m 2.0 m 0.6 m 1.5m P-20 KN Aluminum E70 GPa A-900mm L-1.5 m 1. Axial load at steel rod in kN? 2. Axial stress at steel rod in MPa? 3. Axial deformation of aluminum rod in mm? 4. Axial deformation of steel rod in mm? 5. Axial Load at aluminum rod in kN?
Q3-1 (Trusses), For the Figure shown below; 1 1. Find the forces in the members AB and AD of the truss and indicate whether it is in tension or 3m compression. 10KN 2. Read the following paragraph carefully then answer if it's TRUE or FALSE: The force in the member BC equal to zero? 3. Read the following paragraph carefully then CHOOSE THE CORRECT English Fried Safe 10KN 15 AN 3m 20 kN
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A plate is attached to the frame of a machine by side fillet welds as shown in the figure. Determine the size of the welds to resist a vertical load of 150 kN. Assume that the allowable shearing stress at the throats of the weld is 145 MPa.
Problem No 2 A flanged-bolt coupling consisting of six 4 inch diameter steel bolts evenly spaced around a bolt circle 12 inches in diameter and four inch diameter aluminum bolts on a concentric circle 8 inches in diameter. What stresses are developed on each bolt of the two bolt-circles when a torque T=75 Kip-in is applied. Use Gs=12 x 10° psi and GA = 4 x10° psi.