Answered: Replace the loading system acts on beam…

Replace the loading system acts on beam shown in Fig. (3) by an equivalent system consists (Single Force & Couple at point A). 40 N 3m 30 N 3m 200 N-m 50 N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.43P: Construct the shear force and bending moment diagrams for the beam shown by the area method. Neglect...

See similar textbooks

Similar questions

PART 1 Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 m, b=2.0 m, PB = 2 kN, PC = 2 kN, and MB = 20 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. IMAGE* Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) IMAGE* PART 2 Determine the shear force acting at each of the following locations:(a) x = 0+ m (i.e., just to the right of fixed support A)(b) x = 3.5– m (i.e., just to the left of B)(c) x = 3.5+ m (i.e., just to the right of B)(d) x = 5.5– m (i.e., just to the left of C)When entering your answers, use the shear force sign convention.Answer:(a) V = ? kN.(b) V = ? kN.(c) V = ? kN.(d) V = ? kN. PART 3…
Explain properly and give shear force and bending moment diagrams
Q3: Draw the shear force and bending moment diagrams for the beam as shown below. Also, find the points of contraflexure. (Use method of sections). 6 kN 20 kN/m D 2 m 2 m 2 m
Please asap
Problem 1) Create the appropriate diagrams for the following system. (Load, Shear, and Moment) Identify and comment on the most interesting points. 25 kN/m 5 m 20 kN-m B
For the problem shown below (left), W = 51 lbs while L1 = 4.4 inches and L2 = 12 inches. This results in the shear force diagram as shown on the right, where A, is the reaction force in the vertical direction at point A. Based on this shear diagram, what is the maximum moment in the portion of the horizontal beam from x = O to x = L1 in units of lb-in to two decimal places. (Be sure to use a negative sign to designate a negative moment if necessary.) A |--L1-——————— L2 Ay lb 0 -Ay lb W L1 L2 W -L1- BO L1- -X
Help! Directions: Free Body Diagrams (FBD) must be included for all static equilibrium problems including each section created when solving for internal loadings. Axes and critical points must be clearly labeled on all shear force and bending moment diagrams. Report all answers with 4 significant figures and be sure to include units.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 5 m, b = 3 m, PB = 55 kN, Pc = 75 kN, and PE = 25 kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. a PB Answer: Ay = i BO PB a B Pc a Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) D Pc D a D₂ PE a PE E kN, Dy= i -x E X kN.
For the beam shown, derive the expressions for V and M, and draw the shear force and bending moment diagrams. Calculate the shear force V and bending moment M at a cross section located 0.5 m from the fixed support. Neglect the weight of the beam. (Show complete calculation and step by step process. Show free body diagram)
Draw (internal force) MNT diagrams of the simply- supported beam given 10 kN 6 kN/m 5 kN/m B E 10 kN 3 m -1.5 m -- 1.5 m --– 1.5 m --|
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 m, b=2.5 m, PB = 4 kN, PC = 4 kN, and MB = 60 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Determine the bending moment acting at each of the following locations:(a) x = 0+ m (i.e., just to the right of fixed support A)(b) x = 4.0– m (i.e., just to the left of B)(c) x = 4.0+ m (i.e., just to the right of B)(d) x = 6.5 mWhen entering your answers, use the bending moment sign convention.Answers:(a) M = kN-m.(b) M = kN-m.(c) M = kN-m.(d) M = kN-m.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 m, b=2.5 m, PB = 4 kN, PC = 4 kN, and MB = 60 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.)Answers: Ay = kN, MA = kN-m.