Replace the force system by an equivalent resultant force and couple moment at point O. Take F3 = {-250i +350j-450k}N . determine the resultant and moment 1.5 m 2m F₁ = 300 N 1.5 m F₂= 200 N

Q: 2. A suitcase slides down a ramp between Points A and B as shown below. It has an initial velocity…

A: (a) Write the given data. vi=2 m/sm=2.1 kgμs=0.3μk=0.2

Q: A can of soft drink at a temperature of 4 deg C is taken from a refrigerator into a room where the…

A: The temperature of the can is .The temperature of room is .The relative humidity is .

Q: Calculate the enthalpy of propane in kJ/mole at 1000K assuming a representative specific heat value…

A: Given   Specific heat, CP = 128.7 J/mole.K   Temperature, T1 = 298 K                         T2 =…

Q: A cantilever beam of length l and carrying a point load W at the free end is shown in Fig. 2.41.…

A: A cantilever beam of length l and carrying a point load W at the free end  is shown in fig;

Q: Steel balls (diamęter = 21 mm, p= 7833 kg/m , k = 54 W/m-°C, Cp = 0.465 kJ/kg-°C, and a = 1.474x10 m…

A:

Q: 16. The figure below shows three different arrangements of materials 1, 2, form a wall. The thermal…

A: Given∆T=20°C k1>k2>k3

Q: A 10-ft' tank contains oxygen initially at 14.7 psia and 80°F. A paddle wheel within the tank is…

A:

Q: Q3 - Consider an engine that generates heat at a rate of 8530 Btu/min. Suppose this engine is cooled…

A: given  engine that generates heat at a rate of Qgen=8530 Btu/min The air is fed to the housing at…

Q: 1 kg of air at 1 bar and 27°C is held in a cylinder of 0.8 m° capacity. The gas is heated until the…

A: Here, Initially air is at T1=27°C=27+273=300 K;  p1=1 bar V1=0.8 m3;   R=287 Nm/kg K Final…

Q: 16. K1 and K2 are springs in parallel. They are attached in series to spring K3, which is attached…

A:

Q: other. A twisting moment of 30,000 lb-in. is applied If E-30x10 psi and G-12x10 psi, compute the

A: Given that ,

Q: 2. A vertical square surface as shown in the figure as shown in the figure has its upper edge…

A:

Q: Determine the area moment of inertia Ix of shaded area about the x axis. Determine the area moment…

A:

Q: If let go from rest, the maximum speed the object can have at the bottom of the slide is (see…

A: Given data, h = 1m Mass = m Find Vmax = ?

Q: m /s, v=1.798E-5 m/s, Pr= 0.7228). If the optimum spacing is 12 mm, what is the heat transfer rate…

A:

Q: The material has a specific weight y=99 lb/ft³ (Figure 1) Figure 0.25 t 0.5 ft 2 ft 0 H Q Search 1…

A:

Q: This question is about Material index for Ashby chart. Select the correct material index for the…

A: given; maximize the elastic energy stored per unit mass in the spring.

Q: F SIMPLE STRESSES 2. Based on Problem No. 1, determine the shear stress in the grain of the timber…

A: As per honor code and answering guidelines I can answer 1st question at a time.If you want other…

Q: Part 3 Find the potential energy in the torsional spring in position 1. Answer: V₁1 = i Save for…

A:

Q: Use the property tables (the appendices from Moran & Shapiro) to find the stated properties of…

A:

Q: Five pounds mass of water in a container have a pressure of 15.0 psi and a temperature of 248°F.…

A: Given : The mass of water = 5 lb The pressure of water = 15 psi The temperature of water = 248 °F

Q: A piston-cylinder device contains 4 kg of nitrogen initially at 100 kPa and 25°C. Nitrogen is now…

A:

Q: 10. If Fan #1 is 5hp, 1.5" static pressure, 5,000cfm, and 2,000rpm, what is the flowrate of Fan #2…

A: Given: For fan1: static pressure→P1=1.5'' Flow rate→Q1=5000 cfm Speed of the fan→N=2000 rpm For fan…

Q: For external forced convection with an isothermal surface, what is the Nu# correlation equation for…

A: Nusselt number (Nu) signifies the ratio of conductive resistance to the convective resistance…

Q: 12 The 40-kg disk A with a radius of 0.5 m and the 30-kg crate B is attached to each other using the…

A: Given data: -  The mass of the disk is mA = 40 kg. The radius of the disk is r = 0.5 m. The mass of…

Q: A 0.36 percent Carbon hypoeutectoid plain-carbon steel is slowly cooled from 950 °C to a temperature…

A: Given Data:- Weight % of carbon =0.36 Temperature range, 950 °C to 723 °C To find:-The weight %…

Q: A 3.0 x 1.5m sign is supported by a hollow circular column, which has a 100mm outside diameter and…

A: Given:-         Hollow circular column of outside diameter is:                d2 = 100 nm Inside…

Q: Let's consider a canteliver beam, fixed supported at A, and subjected to the shown load. Determine…

A:

Q: 2. The cart shown below has a total mass of 134 kg. Its center of gravity is located at Point G.…

A: Total mass = 134 Kg P = 632N

Q: The force F = (400i – 100j – 700k} Ib acts at the end of the beam. Determine the moment of this…

A:

Q: A brass boiler has a base area of 0-15 m2 and thickness 1-0 cm. It boils water at the rate of 6-0…

A:

Q: The force F has a magnitude of F =504 N. Express F as a vector in terms of the unit vector i and j.…

A: Given data: F=504 N Need to write in vector form.

Q: Torsion Load 100 mm- Shafts ABC and DEF are made of A36steel. Shaft ABC is connected to an…

A: Given: The motor power, P = 2 kW The speed of shaft ABC, N = 62 rpm The factor of safety of shaft…

Q: Gears A, B, C, and D have radii of 20 mm, 55 mm, 30 mm, and 80 mm, respectively. (Eigure 1) Figure…

A: The angular acceleration of the gear D. Given: The radius of the gear A is rA=20 mm=0.02 m. The…

Q: A smooth can C, having a mass M = 3 kg, is lifted from a feed at A to a ramp at B by a rotating rod.…

A: Here the data are- θ=30° θ'=0.5 rad/s M=3 Kg r=2bcosθ b=600 mm=0.6m

Q: 3 m 5 m YF1 C. A weight is hanging on the structure. The weight exerts a force of F1 = (5.65x10^2)…

A:

Q: 2. Rankine Cycle. Consider a steam power plant operating on the simple ideal Rankine cycle. Steam…

A: State 1: Pump inlet or condenser exit as saturated liquid at P1= 50 kPa State 2: Pump outlet or…

Q: Each spring has an unstretched length of 2 m and a stiffness of k= 260 N/m.(Figure 1) Figure 1 of 1…

A: (a) To find: The stretch in Spring OA. Given: The mass of carte is m=16 kg. The stiffness k=260 Nm.…

Q: defined by v=(25-0.15s) m/s where s is the distance traveled by the car measured from point A. (a)…

A:

Q: An ideal Otto cycle with air as the working fluid has a compression ratio of 8.5. The minimum and…

A:

Q: direction of motion 400 m The standing 400 m time of a car was 10.0s. Question 95 (2000 Question 1)…

A:

Q: 3-The flywheel of an internal combustion engine maintains the smooth rotary motion of the O (A)…

A: 1. The flywheel of an internal combustion engine maintains the smooth rotatory motion of the....…

Q: A 2,900 lb passenger vehicle, with a front cross-sectional area of 45 ft', is traveling on a road…

A: W=Weight of Passenger Vehicle=2,900 lbR=Radius of Horizontal Curve=1300 ftρ=Density of Air=0.0766…

Q: (Figure 1) Figure k-75 lb/ft 0.375 ft 0.75 ft Y Part A If the 250-lb block is released from rest…

A: Weight of block Wb = 250-lb Weight of drum Wd = 60 lb Radius of gyration  ko =0.5 ft Radius of drum…

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: + High-strength bolts are used in the construction of many steel structures. For a given bolt, the…

A: To determine:Required couple(M)

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.