Remove the DC source and replace it with a 12Vp AC (24V peak to peak) source at 50HZ as perFigure 6.VP1VP2VP3VP1VVP2VP31113156.8u100R4C114.7uA15Al1V11416390L1470ARSA 1617R6V650 1212470A'390Figure 81. Calculate the impedance of AC2. Calculate the impedance of the CD3. Calculate the impedance of the DE4. Calculate the impedance of the total circuit5. Calculate the current through ammeter Il6. Calculate the potential difference between A and C7. Calculate the potential difference between C and D8. Calculate the potential difference between D and E9. Calculate the current through Cl10. Calculate the current through LI11. Calculate the current through R6(A

Dear student as per our guidelines we are supposed to solve only one question in which it should…

Remove the DC source and replace it with a 12Vp AC (24V peak to peak) source at 50HZ as per Figure 6. VP1 VP2 VP3 VP1 V VP2 VP3 11 13 15 6.8u 100 R4 C1 14.7u AlL A15 V1 14 16 L1 390 R5 470 A 16 17 R6 V6 50 12 12 470 A' 390 Figure 8 1. Calculate the impedance of AC 2. Calculate the impedance of the CD 3. Calculate the impedance of the DE

Remove the DC source and replace it with a 12Vp AC (24V peak to peak) source at 50HZ as per Figure 6. VP1 VP2 VP3 VP1 V VP2 VP3 11 13 15 6.8u 100 R4 C1 14.7u AlL A15 V1 14 16 L1 390 R5 470 A 16 17 R6 V6 50 12 12 470 A' 390 Figure 8 1. Calculate the impedance of AC 2. Calculate the impedance of the CD 3. Calculate the impedance of the DE

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The zener regulator 5.6 V DC is interfaced with 6.4 V DC relay. How many voltages should be provided by the DC power supply as shown in given Figure?
what are the advantages and Disadvantages Connecting transformers 3 Phase between (delta to Star)
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO- To- : IR Is IT UL-380 V CARGA 1 P₁ = 950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
6. Identify the electronic symbol pointed by the line in the given schematic diagram F A TIP2066 with Heat Sink MA 01 Ohm E Sw TIP2055 wih Heat Sink B 10 Amp 50 PN Bridge Rectiter 0.1 Ohm SW LMTar2 we Heat Sink FUSE A FUSE 10A 230 Voit AC 12V Out o Gnd in 0.1 Ohm Sw 470uF 230112V 10A Transformer 47000UF Sov Output 10 uf 12V10A D A В C D F M CnolIL Choclk
54. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the following a. Equivalent reactance b. Total impedance c. Voltage drop across the capacitor
A Buck Converter converts 24Vdc to 12Vdc with losses of 70W, and a load of 60Ohms. What is the current drawn from the power supply?
From the circuit below, determine secondary winding voltage Vsec if the primary winding voltage Vpri = 120Vrms? %3D Np:Ns 6:1 D. Vp 120 Vac 60 Hz Vout R = 200 Q O 20Vrms O 720Vrms O 120Vrms O Ovrms wi m
answer the following questions
56. A single phase thyristor adjust line spacing converter with a resistive load is shown below: V₂ = V sinest SCR ER R V₂ (B) 1.11 (D) 1.44 If the supply voltage is 230V (rms) at 50 Hz, calculate ripple factor for firing angle a-45" and R - 100 9. (A) I (C) 1.21
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
For the series circuits of the figure below, calculate the total impedance (ZT). R1 4 k2 XL1=4 k2 ZT Xei= 6 k2 Xc2= 3 k2 XL2= 4 k2 Z7= 17.4 kn, the angle is 76.7° Ob. Z7= 17.4 kn, the angle is 56.3° .Oc. Z7= 4.1 kn the angle is -14° Od. Z7= 7.2 kn the angle is 56.3°