Refrigerant-134a at 320 kPa and 408C undergoes an isothermal process in a closed system until its quality is 45 percent. On per unit mass basis, determine how much work and heat transfer are required.
Q: In many refrigeration systems, the working fluid is pressurized in order to raise its temperature.…
A: Given that: Initial pressure (P1) = 140 kPa Final pressure (P2) = 1200 kPa Isentropic efficiency…
Q: Suppose a woman does 500 ) of work and 9500 J of heat transfer occurs into the environment in the…
A:
Q: 3. (a) What is the efficiency of a cyclical heat engine in which 75.0 kJ of heat transferoccurs to…
A:
Q: A system absorbs 362 cal of heat and the same time does 360 J of work. What is the change in…
A: Given, W= 360 J Heat absorbed ,Q= 362 cal= 1514608 J From First Law of Thermodynamics, we have…
Q: A refrigerator, with a compressor rated at 250 W, maintains an internal temperature of 4°C in a room…
A: The power consumed by compressor is W=250 W. The internal temperature is T1=4°C+273=277 K. The room…
Q: Determine in which case is heat added to the system? (a) ΔU = –43 J, w = 40 J; or (b) ΔU = 31 J, w =…
A:
Q: A piston-cylinder assembly contains 0.7 lb of air initially at a pressure of 30 lbf/in² and a…
A: Given: Let us consider the given data, Air's mass, m=0.7 lb Initial pressure, P1=30 lbfin2 Final…
Q: In an Isobaric process ( P = 2.0x105 Pa), increasing the temperature of 10.0 g of liquid water by…
A: P = 2.0x105 Pa temperature =15oC mass = 10 g change in volume = 1.0 x 10-8m3
Q: A system contains 10kg of carbon dioxide (CO2). An isobaric process is performed decreasing its…
A:
Q: a) A Canot heat engine receives heat from a reservoir at 700 C at a rate of 600 kJ/min and rejects…
A: Given: Heat received QH = 600 kJ/min. Temperature of Carnot engine TH=700 oC=973.15 K Temperature of…
Q: An ideal gas undergoes isothermal compression from an initial volume of 4.95 m3 to a fınal volume of…
A: Given: gas : idealprocess : isothermal compressionVi=4.95 m3Vf=2.93 m3n=5.01 molT=36.9°C=309.9 K
Q: (a) How much heat transfer occurs to the environment by an electrical power station that uses…
A: Given data: Heat input, QH=1.25×1014 Efficiency, η=0.44 a) Heat transfers to environment is find…
Q: Air (ρ = 1.26 kg/m3 ) enters a compressor at a rate of 8.50 m3 /min and a pressure of 101.325 kPa,…
A: Given, ρ = 1.26 kg/m3 compressor at a rate of 8.50 m3 /min pressure 618 kPa
Q: heat energy
A: The heat engine cycle shown in Fig. 4 consists of four processes:Process 1-2 is an isochoric…
Q: Carnot refrigerator extracts heat from a freezer at -5.00°C and exhausts it at 25°C. How much work…
A: Given T1 = 25 0 C = 25+273 = 298 K T2 = 273 -5 = 268 K Heat extracted Q2 = 1 J
Q: (a) What is the work output of a cyclical heat engine having a 22.0% efficiency and 6.00×109 J of…
A: a) The expression for the Efficiency is, Therefore
Q: 1.00 mole of an ideal gas occupying 2.00 L is maintained at a constant temperature. An external…
A: Given: The initial volume is 2 L. The final volume of the gas is 0.1 L. The external pressure is 6…
Q: Steam, initially at 700 lbf/in.2, 550°F undergoes a polytropic process in a piston-cylinder assembly…
A:
Q: How much work must be done by a Carnot refrigerator to transfer 1.00 J as heat (a) from a reservoir…
A:
Q: How much total heat transfer is necessary to lower the temperature of 0.155 kg of steam from 145.5…
A: mass = 0.155 kg initial temperature = 145.5 C final temperature = - 15.5 C Total heat energy…
Q: During the early stages of the design of a modern electric power generation plant, you are in charge…
A: Given that----- cooling rate = 2 GW. Increased temperature = 15°F. Question ❓ estimate the flow…
Q: How much work is done per cycle by a Carnot engine operating between +14.0 degrees Celcius and -20.0…
A: Efficiency of carnot engine is,
Q: If the plant operates at 50.0% of its maximum efficiency and its power output is 1.23 × 108 W, at…
A: The given data are: TH=540 KTL=313 KQH=1.23×108 W Here, TH is the higher temperature, TL is the…
Q: n large gas turbine facilities, a heat exchanger called air regenerator is preheated by using the…
A: The Outlet Temperature can be calculated by balancing the energy , where the final enthalpy is to be…
Q: a) The efficiency of a particular cyclical heat engine is 41%. If 371 kJ of heat are being…
A: Given data: Efficiency of heat engine is, η=41% = 0.41. Heat supplied to engine is, Q1=371 kJ.
Q: When a gas follows path 123 on the PV diagram in the figure below, 415 J of energy flows into the…
A:
Q: how much work is required to compress 15.00 mol of air at 20.0 degrees celsius and 1.00 atm to 1/10…
A: number of moles = 15original temperature = 20C = 293 K original pressure = 1 atm original volume = V…
Q: Heat is added to 1.0 mol of an ideal gas at a constant pressure of 1.0 atm, and the volume increases…
A: Ideal Gas under Constant PressureHere's the breakdown of the results for the ideal gas at constant…
Q: One mole of an ideal gas is kept in a container at an initial pressure of 2 kPa and temperature . It…
A: The first law of thermodynamics is just energy conservation law for thermodynamical process. It says…
Q: A fluid at 0.7 bar occupying 0.06 m³ is compressed reversibly to a pressure of 9.7 bar and specific…
A: Given: P1=0.7barP2=9.7barP3=1.3barV1=0.06m3V2=V3v=0.5m3/kg
Q: A prototype engine was built and tested, during the non-flow process it is observed that the Work…
A:
Q: A refrigerator is rated at 370 Watt. What is the maximum amount of heat it can remove in 1 min if…
A:
Q: If an engine operates between 269°C and 26°C, what is its maximum thermodynamic efficiency (as a…
A:
Q: How long in minutes does it take a 1000W electric kettle to bring 1.0L of water to the boiling point…
A: A) Power = 1000 W volume of water = 1 L initial temperature = 15oC mass of iron = 400 g Efficiency =…
Q: A steam engine takes heat from steam at 221 °C to do work. If the surrounding air at 25 °C is…
A:
Q: se 24 kg of 93.5° C water is placed in contact with 24 kg of 11.5° C water. A) what is the enegry…
A: Given:- Suppose 24 kg of 93.5° C water is placed in contact with 24 kg of 11.5° C water. Find:- A)…
Q: Steam enters an adiabatic turbine at 8 MPa and 500°C at a rate of 3.5 kg/s and leaves at 10 kPa. If…
A: SOlution: given that P1 = 8 MPa P2 = 10 kPa T1=500 C P =2.5 MW mass flow m=3.5 kg/s
Q: When 5.8 x 105 Jof heat is added to a gas enclosed in acylinder fitted with a light frictionless…
A: (a) work done by the gas W=PV2-V1=1.01×105 Pa4.1 m3-1.9 m3=2.2×105 J
Q: A Carnot refrigerator is maintaining foodstuffs in a refrigerator area at 4.44°C by rejecting heat…
A: This is based on thermodynamical principle and working of refrigerator.
Q: During an adiabatic process on an ideal gas at 74 deg.C, the air increases its pressure from 178.2…
A:
Q: Check my work mode: This shows what is correct or incorrect for the work you have completed so far.…
A: The PV diagram shown is for a heat engine that uses 1.170 mol of a diatomic ideal gas as its working…
Refrigerant-134a at 320 kPa and 408C undergoes an
isothermal process in a closed system until its quality is 45
percent. On per unit mass basis, determine how much work
and heat transfer are required.
Trending now
This is a popular solution!
Step by step
Solved in 4 steps with 6 images
