Referring to figure assume that the diameter of the rivet that joins the plates is d = 20 mm. The working stresses are 120 MPa for bearing in the plate and 60 MPa for shear in the rivet. Determine the minimum safe thickness of each plate.

Referring to figure assume that the diameter of the rivet that joins the plates is d = 20 mm. The working stresses are 120 MPa for bearing in the plate and 60 MPa for shear in the rivet. Determine the minimum safe thickness of each plate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

can you help me with this
Q-1 Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Мра steel bronze A= 300mm2 E=83 Gpa 900mm2 E=200 Gpa L=4m L=3m 3m 3m 1m In the fig three rivets of 25 mm diameter joins the plates that are each 130 mm wide .The shearsress in the rivet is 80 Mpa and the stresses in the bearing are 120 Mpa . Determine .a)The minimum thickness of each plate .b) the largest average tensile stress in the plate 25mm Ø 130 Q-3 Two solid shafts of different material are rigidly fastened together and attached to rigid supports as shown in fig .Compute the maximum shearing stress developed in the assembly 3 m 2 m aluminium G=83 Gpa steel G=28 Gpa 50 mm dia 25 mm dia T= 2 kN .m
The figure shows a flat hanger bar for supporting shop equipment in a factory. The bar is fixed to a support by means of a bolted connection. The main part of the hanging bar is 1.5 inches wide. This width varies up to 3.0 inches. A 1.0-inch diameter bolt transfers the hanger bar load to the two top bracket plates. Determine the allowable stress of the tension load P in the hanger in the following two instances: to. The allowable tensile stress in the main part of the hanger is 16,000 psi. b. The allowable stress load between the hanger bar and the bolt is 26,000 lb/pu.
A pin connection, like that shown in Figure -16, is subjected to a force of 16,5 kN. Determine the shear stress in the 12.0 mm diameter pin.
20 FF 170 A 30 Ölçüler mm cinsindendir. A-A kesiti When the torture in the figure squeezes the material, the maximum force F in the clamping jaws is 1 kN. Calculate the maximum normal stress in section A-A according to the given?
asap pls
15 kN 2) Two objects are glued on the angled plane as shown in figure. If the ultimate stress for the glued joint are 20 MPa and 10 MPa for tension and shearing stress respectively, find the value of 0 that corresponds to the maximum factor of safety and find the value of this maximum factor of safety. 0.035 m 0.05 m
Q8(): For the truss shown in the Figure, if the diameter of pins at A and G are 3 in and 2 in, respectively. Both stresses in A and 70 kips 50 kips 4 ft B 4 ft are double shear. Determine the shear stresses in pins at A and G and the stresses in 9 ft members AG; AF member GF if their diameter is 4 and in.
Please don't provide handwritten solution .....
Given:a. the force in BD=25KNb. vertical reaction at point C=-10KNc. horizontal reaction at point C=15KNd. resultant of reaction at point C=18.0KNe. allowable tensile (normal) stress in member BD =83.33MPaf. the allowable shear stress in the pin at C =72.7MPaPlease help me solve for:1. What is the required cross-section area and minimum thickness t of member BD?2. What is the required SHEAR cross-section area at point C?3. What is the minimum diameter for the pin at C?(Solve for a value with the combination of mm and N)
In the figure, two planks are fastened together with a sheet plate with a thickness of 4 mm. Since 1 kN load is applied to the plank; a) The maximum normal stress occurring in the plate, b) Find the shear stress on the M10 bolt and the bearing stress on the plate (the thread bottom diameter of the M10 bolt is approximately 8 mm)
4) The C-clamp shown below has rectangular cross-section A-A that is 33 mm tall by 12 mm wide and the material is class 50 gray cast iron. Determine maximum tensile stress and factor of safety for clamping force F = 3.2 kN. Ignore stress concentration factors. See Section 4.9 in Norton for help with curved beams. MPa N O MAX |F F 60 mm 40 mm 12 mm 33 mm 33 mm Section A-A A