Refer to the graphic. This motherboard supports a maximum of 32 GB. This motherboard supports dual channeling if the modules in memory slots 1 and 3 match, if modules in memory slots 2 and 4 match, OR if modules in 1 and 3 match along with the modules 2 and 4 matching. This is a new motherboard. The user wants 4GB of memory. What solution is best for implementing dual-channeling and leaving space for the user to upgrade in the future? Select the best answer.

Refer to the graphic. This motherboard supports a maximum of 32 GB. This motherboard supports dual channeling if the modules in memory slots 1 and 3 match, if modules in memory slots 2 and 4 match, OR if modules in 1 and 3 match along with the modules 2 and 4 matching. This is a new motherboard. The user wants 4GB of memory. What solution is best for implementing dual-channeling and leaving space for the user to upgrade in the future? Select the best answer.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Describe the bus connections required to implement a TOY-8 branch and link command. 7.5.6 In our TOY-8 CPU circuit, how many switches are there? Make a table that shows the number in each module as well as the overall (with percentages).
Q5/ answer the following questions : 1- Which type of instruction dose INTO normally follow? Which flag does is test? 2- In a minimum-mode 8086 microcomputer, which signal indicates to external circuitry that the current bus cycle is for the /0 interface and not the memory interface? 3- Which type of 1/0 has the disadvantage that all /o data transfers must take place through the AL or AX register? 4- How many bytes of memory does an interupt vector take up? 5- In a maximum-mode system, which device produces the input (read), output (write),and bus control signals for the /0 interface? 6- How many address lines must be decoded to generate five chip select signals? 7- What do you mean by pipelined ? 8- Draw the register organization of 8086. 9- At what address are CS40 and IP4 stored in memory? 10- If a physical address is 5A230 when (CS) = 5A00, what will it be if the (CS) are changed to 7800?
Imagine you're constructing an embedded system on P2.1 that use timer 0 to generate a 70% duty cycle and timer 1 to generate a 30% off cycle. It will read data from P1 while also transferring data to a serial device. Describe if the system requires a real-time operating system.
How can BitLocker be implemented on Windows systems lacking a TPM chip on the motherboard?
Which of the following DMA Transfer Modes is the worst in term of hardware cost: a.Cycle Stealing b.Block Transfer Mode c.Burst mode d.Transparent mode
Which one is the correct option about the features mentioned for Arduino and Raspberry Pi microcontroller boards.1. Raspberry Pi has more processing capacity as compared to Arduino2. Arduino consumes more power than Raspberry Pi. a. 2 is true only b. Both 1 and 2 are true c. Both 1 and 2 are false d. 1 is true only
Transfer rates for character devices are often higher than those for block devices. Is this a true or false statement?
3
i need the answer quickly
Let's pretend you're programming an embedded system, and that you want P2.1 to operate at a 70% duty cycle and a 30% off cycle, respectively, using timer 0 and timer 1. Data is being read from P1 and sent to a serial device concurrently. Give your reasons for or against using a real-time OS in this scenario.
. IHow many devices can be used on a single SCSI bus? Keep in mind that the SCSI host adapter counts as a device. A 1 8. C 20 D 10
Which input port in the circuit of the Figure below is selected for input operation if the address within the I/O space is 1F03H? Required to answer. Single choice. A. Port 0 B. Port 1 C. None of the port is selected by this address D. Any port can be selected by this address E. Port 2