Refer to the braced cut shown in the figure for which y= 20 kN/m², o'=23°, and c' = 0. 2.0000 The struts are located 5 m on center in the plan. Determine the strut load at A. 3.0000 3.0000 2.0000 A 1186.45 kN В 237.29 474 26 1816 29

Refer to the braced cut shown in the figure for which y= 20 kN/m², o'=23°, and c' = 0. 2.0000 The struts are located 5 m on center in the plan. Determine the strut load at A. 3.0000 3.0000 2.0000 A 1186.45 kN В 237.29 474 26 1816 29

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Prestress force (at transfer). P = 2000 kN, is applied at 50mm below centroid. Losses between…

Q: What is the distance of the neutral axis from the extreme compression concrete

A: Distance of the neutral axis from the top of the beam M = Cy M = 1/2*fc*bx(d-1/3*x) 580(10002) = 1/2…

Q: 1. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm…

Q: 1. Steel column 7 m long and fixed at both ends is used to carry an axial load of 650kN. The column…

Q: A T-Beam has the following properties: Effective flange width, b = 800mm Flange thickness, t₁f =…

A: Area of compression block Ac= As fy / (0.85 f'c) = 8000 x 275 / (0.85 × 21) = 123249.30…

Q: b=148mm d=266mm A=5700mm² 1₁=7.03E6mm4 |x=71.1E6mm4 E=200GPa Pinned at top. Fixed at its base.…

Q: 5. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm…

Q: Determine the forces in members CF, CG, and CD of the truss shown by method of section. Use P,=8 kN,…

Q: Calculate the absolute deflection at point (c) for the truss showing in figure below by using unit…

A: The beam is a horizontal member of the building or structure. It can use to transfer the load from…

Q: Using portal method, Calculate for the shear force in kN at member FC a = 12.6 kN, b = 27.2 kN, c =…

Q: The beam is 7m long with EI = 200MNm^2 Let P = 10 kN Find: 1. Slope at 2m from A. 2. Deflection…

A: To find slope and deflection at C which is shown in the figure

Q: Q1: Design a simply supported rectangular reinforced concrete beam. Take = 28 MPa, and fy = 420 MPa.…

A: The given data is: Width of the beam, b=300mmThe total depth of the beam, h=500mmfc=20Mpafy=420Mpa…

Q: www.m 2m P B Im Im UND OB çubuk enkesiti D=12cm With using TRESCA method Calculate the force P that…

A: The yield stress that section can safely carry = 480 MPaThe factor of safety (n) = 2For a circular…

Q: P = 12 KIPS In a section ABC, sufficiently far from the post to remain plane, determine the stress…

A: P = 12 kips 10 in x 10 in column

Q: 1. A rectangular beam with b = 250 mm and d = 460 mm is re only with 3-25 mm bars. The beam is…

A: fy=276.5MPa fc'=20.7MPa

Q: The cantilever beam shown has the following dimensions: a = 300 mm; b = c = 400 mm; d = g = 24 mm; e…

Q: Need help with this question

Q: 1. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm…

Q: Q1. Figure 1 represents the truss system for a billboard. Point loads at joints D and E and dur to…

A: MF=0109.9×15+109.9×7.5-A8=0A=309.09kN ↑Fy=0309.09+Fy=0Fy=-309.09kN↓Fx=0-109.9-109.9+Fx=0Fx=219.8kN→…

Q: Using W27X102 as the section for the beam, determine the value (kN) of the nominal collapse load Pn.…

A: Solution: Given: Section: W 27 x 102 L =3.6576 m fy = 345 MPa

Q: Q\ Analysis the truss below. P=7 kn P= 7 kn 20 KN Figure 1 6.67 m 6.67 m 6.86 m 6,86 m 6.86 m 6,86 m…

Q: The rectangular beam ABC, 175 mm wide by 411 mm deep, is supported by a pin at A and the cable CD.…

Q: 600 cm 600 12 KN 1 kN 400 3 kN 4 kN 400cm 400 300 600 cm 300

Q: A concrete pier 20 in. X 24 in. supports a load of 100 kip at point E as shown. Determine the…

A: To determine: Stresses at each corner and location of Neutral axisCase-Iey=0ez=4 inchCase-IIey=6…

Q: The rectangular beam ABC, 175 mm wide by 411 mm deep, is supported by a pin at A and the cable CD.…

Q: SITUATION II: A reinforced concrete beam 320mm and effective depth 537mm is used as a cantilever on…

Q: Use the method of sections to solve for EG, GH, and HJ. 1 kN 2 KN 2 kN 2 kN 1 kN H F 0.46 m D 2. 62…

A: Consider the figure,

Q: The Channel section is used as a purlin placed on top of trusses with spacing of 4.9 m and slope 1V…

Q: 25M meter of the column in the ne nber of diameter 28mm longitu

A: Given:- deadload=1530kN live load-1420kN 12mm dimaeter f'c=30MPa fy=425MPa To find:- a) diameter of…

Q: Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m.…

A: The lever will induce an axial force P and a clockwise moment Pe at the point C. Using equations of…

Q: Use the method of sections to determine the forces in truss members FI and EG.

Q: c. The moment capacity of the column.

Q: A Ax = Note: Point C is 1.5m below left support A. kN B 6 kN 6 m3 m Ay = 1.5 m. C D 12 kN mk 4 kN E…

A: Given data Find support reaction at A (Ax and Ay)

Q: 1. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm…

A: Given data b = 250 mm, d = 460 mm fy = 276.5 MPa fc' = 20.7 MPa Find maximum steel ratio

Q: Calculate the design moment capacity of a 300mm × 500mm pretensioned beam

Q: A simply supported beam with spans of LAB= 11 ft and Lac 33 ft supports loads of w- 3.0 kips/ft and…

A: Determine the magnitude of: (a) the maximum horizontal shear stress in the beam (b) the maximum…

Q: If the allowable bending stress is callow 6 MPa, determine the minimum dimension (d) of the beam's…

Q: .Using the method of sections, determine the force in member 7 Given: a = 0.6 m, b = 2.4 m,d= 1.2m…

Q: 6 m E9 F.

A: First, calculate the C.G A×8+A×14=3A×xx=7.33Ration of forces=Ratio of their CG from…

Q: For the truss shown, determine the force in member 3. Given F1 = 96 KN; F2 =192 KN and a =3 m F2 a/3…

Q: Q#1: Explain in your own words the concept of influence line. (CLO1)(PLO1)

A: Thank you for the question . As per honour code we will answer the first question since exact one…

Q: 2. Analyse the following truss finding all member forces. 7.4 kN 6.4 kN 3m B 2@4 m

A: Given Above diagram of truss with vertical load = 7.4kN and horizontal = 6.4 kM

Concept explainers

Pressure and Stress

Question

Refer to the braced cut shown in the figure for
which y= 20 kN/m², o'=23°, and c' = 0.
2.0000
The struts are located 5 m on center in the plan.
Determine the strut load at A.
3.0000
3.0000
2.0000
A
1186.45 kN
В
237.29
474.26
D
1816.29

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

100% SURE PLEASE
Refer to the braced cut shown in the figure for which y= 20 kN/m², o'=23°, and c' = 0. 2.0000 The struts are located 5 m on center in the plan. Determine the strut load at B. 3.0000 B. 3.0000 2.0000 A 47.46 B 474.6 C 94.92 D 237.3
1 of 1 60 60 АВ BC CD DI HI GH 53.130 \53.130° 53.130 \53.130° FG EF C D EA ЕВ 60 FB BG Use truss by joints GC GD Solve for the magnitude of all members and determine if they are in tension or compression. HD Support reactions are already calculator for you. Ax = 270 kN right Ex = 270 kN left Ey = 180 kN up %3D Keep calculations to 2 decimal places. Units are kN. One grid = 1m
From the figure shown, 10' kN 3 m 20 kN 5 m 3 m 5 m В C a. Determine the axial force of girder GH. b. Determine the axial force of column EH. c. Determine MA, MB and Mc.
Determine the bar force member CD. All interior angles are 60 degrees.
1. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm bars. The beam is simply supported over a span of 6 m and carries a uniform dead load of 0. 680 KN/m including its own weight. Use fy=276.50 MPa and fc'=20.70 MPa. The maximum steel ratio is . 0.0128 0.0096 0.0278 0.0371 0.0167 0.0224
A cantilever beam with length of 3.2 m is reinforced with As=5720 mm^2 tension reinforcement and compression reinforcement A's =1905 mm^2 placed at 60 mm from extreme compression fiber. The effective depth is 550 mm and width of 400 mm. Use f'c=35 MPa and fy=415 MPa. 1. Calculate the magnitude of the neutral axis. 2. Determine the compressive force of the section. 3. Determine the safe concentrated live load that can be placed at the free end if the beam carries a total ultimate uniform load of 35 kN/m.
A W6 X 116 section is to serve as a purlin between roof trusses which is 7.2 meters on center. The roof is assumed to support a dead load of 960 N/m^2 including its own weight and a live load of 894.154 N/m^2. The slope roof truss is 1 vertical to 2 horizontal and the purlins are to be spaced at 1.8m on centers. Using A36steel with Fy=248 MPa. Assume all loads will act at the center of gravity of the section. Sag rods are to be placed at the middle thirds between trusses. Properties of W 6 x 116 A=3058 mm2 d = 159.51 mm bf = 102.36 mm tf = 10.29 mm tw = 6.60 mm Sx = 167 x 10^3 mm3 Sy = 36 x 10^3 mm3 Using DL+LL only a. Determine the bending stress along the Normal axis bending in MPa b. Determine the bending stress along the Tangential axis bending in MPa c. Determine the DCR if the capacity Fbx = 0.66Fy and Fby = 0.75Fy really need the answer
Define particular volume, specific gravity, and viscosity. Include Newton's law of viscosity as well.
Figure Q2(a) illustrates the plan view and sectional view of a simple structure. Slab ABCD is supported by beams along AB, BC, CD and AD. The columns are located at points A, B, C and D. Consider the factored loading on slab is 8 kN/m? and factored self-weight of beam 2.5 kN/m. Calculate the total loading to be supported by column A. - 6 m A В 2.75 m C D Plan view 6 m Slab Вeam -Beam Column Column Section X-X view Figure Q2(a)
For the given truss, determine the force in member 6. Given F = 84 KN. %3D II 4 IV 8 1 5. 7 60° 60° I 2 III 6 V F A. F6 = -194.0 KN B. F6 = -145.7 KN C. F6 = 48.7 KN %3D D. F6 = 97.0 KN E. F6 = -48.7 KN
Q2/ Determine the forces at the pin joint (F) and the roller support (G) ? 30KN 20KN 2m By 2m D 2m E G = 130 KN, Fx = 130 KN, and Fy = 50 KN %3D %3D G = 50 KN, Fx = 70 KN, and Fy = 100 KN G = 0 KN, Fx = 0 KN, and Fy = 50 KN All of the above 2m