1. Determine the maximum shear 2. Determine the maximum moment. Problem For the figure as shown below, a uniform load of 112 KN/m is acting downward and supported by an upward uniform pressure of q = 48 KN/m. 112 kN/m 112 kN/m q=48 kN/m 1m 1.5m 2m 1.5m 1m

1. Determine the maximum shear 2. Determine the maximum moment. Problem For the figure as shown below, a uniform load of 112 KN/m is acting downward and supported by an upward uniform pressure of q = 48 KN/m. 112 kN/m 112 kN/m q=48 kN/m 1m 1.5m 2m 1.5m 1m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam AB = 10 m has a hollow rectangular cross-section with 17 cm as width, 28 cm as depth and inner thickness as 2 cm is subjected to a point load of 7 N & 5 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 2 m & CD = 2 m. i) Reaction force at B in (N)= ii) Reaction Force at A in (N) = iii) The distance from B at which the shear Force value changes from "-" to "+" in (m) = iv) Maximum Bending Moment (Please write the Maximum bending moment valve in (Nm) = v) Moment of Inertia, I in (m^4)= vi) Maximum bending stress in (N/m^2)= vii) Bending stress at 2 cm from the top in (N/m^2) =
A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.5 MPa. Answer must be in kN/m. Given: b = 130 mm and d = 170 mm.
Given: Maximum positive shear = 387.50 kN Maximum negative shear = 602.50 kN Maximum positive moment = 1970.65 kN-m Maximum negative moment = 1480 kN-m Location of maximum shear from the left end of beam = 22 m Location of maximum moment from the left end of beam = 15.23 m Determine the maximum bending stress (in MEGAPASCALS on the beam) given the cross-section on figure. Note: Measurements in figure is in millimeters. Kindly Draw the Shear and Moment Diagram or FBD if necessary. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
1. A 6.4 - m beam has a pin support at the leftmost part of the beam and a roller support located at 4 meters from the pin support. It carries a uniformly distributed load of 40 kN/m throughout its entire length. Using shear and moment diagram, A. Calculate the maximum shear. B. Calculate the maximum moment. C. Determine the most economical and lightest S-shape if the flexural stress is equal to 120 MPa. D. Calculate the actual bending stress of the chosen beam.
A very important load on a structure is earth thrust loading. This one loading can be simplified for mathematical calculations as being a trapezium. In this case, from a retaining wall the force of the earth will be horizontal. The earth pressure is distributed decreasingly with the height. This structure is shown below, calculate all three support reactions acting in section A. Where B is given in kN/m and H in meters. (Ignore the weight and thickness of the frame) consider: В- 60 5 kN/m H= 90 | Hm (B+5)kN/m A
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 10 cm as width, 23 cm as depth and inner thickness as 2 cm is subjected to a point load of 8 N & 9 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 1 m & CD = 1 m. iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I = vi) Maximum bending stress = vii) Bending stress at 2 cm from the top =
In the system shown in the figure, parts AB, BC and CD are of equal length and 4 m. Clockwise from point AA moment of 10 kNm is applied in the opposite direction. The distributed load of 3 kN/m at BC is upward. Beam DA load of 5 kN was applied downwards from the point. The profile of the beam has a 100 mm edge as seen on the right side.was formed by subtracting a circle with a diameter of 80 mm from the center of a regular hexagon of length. Accordingly; A)Calculate the reaction forces at B and C B)Draw shear force and bending moment diagrams C)Calculate the maximum bending and show it on the bending moment diagram. D)Calculate the sectional moment of inertia of the profile E)Calculate the maximum stress in the beam NOTE:For option C, you need to obtain a parobolic expression when drawing the bending moment diagram. You need to use derivation.
3. In the figure, compute the maximum force P that can be applied, if the shearing stress in the pin at B and the axial stress in the control rod at C are limited to 3200 psi and 4500 psi, respectively. The diameters are 0.2 inch for the pin, and 0.45 inch for the control rod. Assume double shear for the pin at B. в с 1.5 in 78 degrees T 6 in 2 in
A torque of magnitude T = 1000 N-m is applied at D as shown. Shaft AB and CD have an elliptical cross-section. The major and minor diameters of shaft AB are 56 mm and 50 mm respectively, while the major and minor diameters of shaft CD are 42 mm and 38 mm respectively. Find the maximum shearing stress in shaft CD. Answer must be in MPa
A 14-m simply supported overhang beam is supported at x = 0 and x = 10m. The overhanging portion is from x = 10m to x = 14m (the overhang portion is 4m). A uniform 20 kN/m load is from x = 0 to x = 5m and a 30 kN concentrated load is at x = 14m (or the right end). Find the value of the maximum positive moment.
Problem # 1: A hollow shaft has an outside diameter 60 mm and a wall thickness of 1.25 mm. The maximum shear stress in the shaft must be limited to 150 MPa. Use G = 43 000 MPa. Determine: (a) the maximum power that can be transmitted by the shaft if the rotation speed must be limited to 20 Hz. (b) the magnitude of the angle of twist in a 700-mm length of the shaft when 30 kW is being transmitted at 8 rpm.
G=5 M=9 Given: 25 kN and 18 mm