Refer to Fig. TOS-OM-07. For the indeterminate beam shown, assume El = constant, solve for the following: Vertical Reaction at support Cin kN 40KN 20kN 30KN/m 30KN/m A 2m 3m 2m 1m Fig. TOS-OM-07 O Zoom image 24.54 42.28 118.13 113.18

Q: [Select] of gear B (d) the tangential acceleration

A: Given,  Normal acceleration at gear B, αB= 372.604 Radius of gear B, rb= 175mm

Q: (Bernoulli/continuity) Water flows steadily through a diverging tube as shown in the figure below.…

A: Given data: d1=0.52 ftd2=0.70 ftd3=0.92 ftSG=2y=2.4 ft

Q: Problem 2. The following observations were taken during a tacheometric survey using the stadia lines…

A: Given- The observation obtained from tacheometric survey using stadia lines of a theodolite.…

Q: A 40-lb aluminum bar, initially at T₁ = 150°F, is placed in a tank together with 190 lb of liquid…

A: Given data: Weight of aluminium bar=40 lb Temperature of aluminium, Ta=150°F Tank of water with…

Q: 3.) Consider the 2D frame shown below. There are pins at A, C, D. Point E is halfway between A and…

A: Find:

Q: 3. Calculate the SDI for the following samples. Determine if the water needs to be pretreatment…

A: To calculate the SDI, we use the following formula:SDI = (1 - Ti / Tf) * 100 / Ttwhere:Ti is the…

Q: g) At what single point along the beam does this maximum occur? h) What are the values of internal…

A:

Q: PC1 PI1 0+000 Lct PT1 R1 11 STATION NORTHINGS EASTINGS 0+000 11475.55 8927.24 PC2 9291.91 9546.66…

A: To Determine Table 3 ( The Stationing of PC, PT, PC2, PCC, PT2, PC3, PRC, PT3 and End of Project)…

Q: For the beam shown (E = 200 GPa, A=12 cm², I-9 cm¹), determine: a) Reactions at A and C. b) Draw the…

A:

Q: Label the maximum and minimum values on the graph. d) Draw the internal bending moment diagram (BMD)…

A:

Q: 1-66 Figure P1-69 shows a bolt subjected to a tensile load. One failure mode would be, if the…

A: Force = 22.3 kN or 22300 NDiameter of shank, d = 12 mm Thickness (t) = 8mm

Q: a) Compute the difference in elevation between A and B. b) Compute the difference in elevation…

A:

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: Explain the formula of fs

A: From the original solution: Given: Width, b = 18 in Effective depth, d = 26.5+2.5=29 in. Height of…

Q: Water flows in a steel pipe (ɛ = 0.00020 feet) at a flow Q = 12.5 cfs. The diameter of the pipe is D…

A: Given that:                           Surface roughness, ∈=0.00020 ftDischarge, Q=12.5 cfsDiameter…

Q: Problem 2. A well is located in a completely confined aquifer with a hydraulic conductivity of 12…

A:

Q: A rectangle of an elastic material is deformed in the x, y plane as represented by the dashed lines.…

A: Given: E=300 MPa  and poisson ratio μ=0.4No deformation in Z directiona Normal strain strain in x…

Q: d. Calculate that "certain angle" using differential calculus. (Use the principle of Maxima-Minima)

A:

Q: A well pumping test was carried out in an unconfined soil layer of thickness 15 m to determine its…

A: Given data in question  Unconfined aquifer  Discharge  Drawdowns Radius of influence  Total height…

Q: Determine the MOMENTS acting at the ends of each member of the frame shown below. Assume the…

A:

Q: 3. Name any two-pattern material.

A: Introduction- There are several types of material found in nature. Some materials form certain…

Q: 1. Highway functional classifications include arterial, collector, and local road, respectively for…

A: "Since you have posted multiple questions, we will provide the solution only to the first three…

Q: The simply supported beam shown below is homogeneous, prismatic and has a distributed axial load of…

A:

Q: Please do parts d, e, and f.

A: Part d, e and f is to be solved

Q: Given the following information Distance Azimuth (m) Course Bearing Latitude Departure N 60°00' W…

A: Answer:- Latitude and Departure:

Q: a) top most, hef tmost

A: X = 1.5 cm Y = 5.48 cm

Q: 6. A biodegradable fuel having a specific gravity of 0.95 and a viscosity of 0.04 grams per cen-…

A: Solution (6) Reynolds number of the biodegradable fuel is calculated by. Re =ρvDμv =Re ×μρD Where, ρ…

Q: Water flows at a rate of 120 L/s in a 30 cm diameter horizontal pipe connected to a 20 cm diameter…

A: Given discharge= 120 L/s  Dia of horizontal pipe = 30 cm  Dia of vertical pipe = 20 cm

Q: Question 1 A vertical circular gate in a tunnel 8 m. in diameter has oil (0.80) on one side and air…

A: Solve letter A only Given- diameter d=8 m,air pressure P=40 kPa,oil height=12 m, Hydrostatic force=?

Q: Derive the expression

A: Expression for change in length of the block

Q: 4.) Consider the 2D beam supported by a pin at A and a roller at B. EXTERNAL FORCES a) Draw a FBD.…

A: Find:

Q: A simply supported wood beam with a span of L = 13 ft supports a uniformly distributed load w. The…

A:

Q: 1. Y 3" r= 3" 4" 1" 2"

A:

Q: Problem 12.16 Consider the building frame shown in (Eure) Suppose that My 2.6 k/ft and s8 k/ft.…

A:

Q: (Knowing that the linear expansion of steel is a = 15.5×10-6 K¯'). How the change of the beam…

A: Using formula for expansion or contraction due to temperature changes

Q: Classify the structure shown in the figure. OA. Indeterminate. 21st degree O B. Indeterminate, 24th…

A:

Q: Design a tie column to carry an axial dead load of 600 kN and an axial live load of (1.6X1+2.6X2)…

A: Given  Fy=X2=403MPaFc=X1=67.9MPaDead load=600kNlive=1.6X1+2.6X2Total=600+1.6×67.9+2.6×403…

Q: Please do Part C, E, and F

A: To solve part C,E and F

Q: f. Assuming a porosity of 18% for the sandstone, what is the seepage velocity for that unit? g. How…

A:

Q: #3 Classify each of the following trusses as statically determinate, statically indeterminate, or…

A:

Q: 1. Compute the slope at B and deflection at points B & C of the Beam shown. Use the Double…

A:

Q: A W21x73 is supported on simple supports on a 30-ft span. Calculate the plastic moment Mp. Assume…

A: From Table, I=1600 in4 d=21.2 in y=d2=21.22=10.6 in MyI=fyyMy1600=5010.6My=7547.16 kip.in Yield…

Q: Water flows from a tank through 160 feet of 4 inches diameter pipe and then discharges into air as…

A: Given data,  n= 0.013 Discharge, Q= 12 cfs Length of pipe = 160 ft Diameter of pipe = 4 in To find…

Q: cup device. Number of blows 6 12 20 28 32 Water content (%) 52.5 47.1 43.2 38.6 37.0 Two…

A:

Q: SQ1. The bars AB and BC are joined by a pin at A and a horizontal cable. The vertical cable carrying…

A: Free Body Diagram:- tan30 = AB5 AB = 2.887 m sin 30 = xAB x=2.887*sin30 x=1.4435m sin30=y3 y=1.5m…

Q: 2. A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial…

A: Note :- as per our guidelines we are supposed to answer first three subparts only. Please repost…

Construction Process

In civil engineering, construction is the combination of art and science, to construct a physical and naturally built environment, starting from the design phase. The construction process falls under the area of building construction, which is a sub-branch of civil engineering. Hence, it is also sometimes called the design and build or design-build process. The work of construction is majorly carried out by civil engineers and design professionals along with a team of works consisting of contractors and subcontractors.