reading in mm and inches of the two

Q: 1.3 Determine the length of side a and the measure of the two acute angles. 72.0' 67.3'

A: find the side a and two acute angles.

Q: A compressor motor has a shaft diameter of 7⁄8 inch. The felt wiper that wrapstightly around the…

A: Given    Diameter,d = 7⁄8 inch.

Q: How much force in lbs will it take to lift a 10 -lb weight with a wheel and axle, when the axle is…

A:

Q: 4 5/8" as meters

A: Given-4 5/8" or 4 5/8 inch To find-change the length into meter

Q: Find in inches the inside diameter of this water pipe for an automatic icemaker. Express the answer…

A: Given     Outside diameter, d = 1 1/4 in                                  = 1.25 in…

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: draw the left side

A:

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: What are the two dimensions that are not placed on the field of a drawing? A zero and a 45 degree…

A: The following things needs to be mentioned on the field of drawing: ◆ The diameter or radius of…

Q: 8. This sheet metal section has 5 sets of drilled holes: A, B, C, D, and E. The holes within a set…

A: Given: The set of holes are equally spaced in horizontal direction. The five sets of drill holes are…

Q: Problem 1: a) Draw the free body diagram of the member ABC? b) Determine the reaction forces at the…

A:

Q: Find ex, ey and y. NOTE: ex and ey in mm/mm and y in radians.

A:

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: Engine piston weight 220 g. Machine speed 4700 rpm. What is the high acceleration of the piston when…

A: The weight of engine piston is given as, w=220 g. The machine speed of the engines is given as,…

Q: What is the precision measurement of 1 7/8 inch

A: PRECISION IS DEGREE TO WHICH REPEATED MEASUREMENTS UNDER THE SAME CONDITIONS SHOW THE SAME RESULTS.

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: 4 = 2, B= 3, and the angle formed by A and B is 60°. Calculate the value of 4+ 2B. Round your answer…

A:

Q: 3. It is desired to design a 5-cylinder aircraft engine with a stroke-bore ratio of 1.2. The piston…

A: here, stroke bore ratio say, l/d ratio = 1.2 so, l = 1.2×d volume per cylinder = π4·d2·l here,…

Q: Write a CNC program code to machine this part.

A: Since the part is symmetrical, thus divide the given component into half and the half part.

Q: A drilling machine is to have 8 speeds ranging from 100 rev/min to 1000 rev/min. if the speeds from…

A: The total number of terms for this AP is: n=8 The first number is: a=100 rev/min The last number is:…

Q: The steel box wrench (E=29,000ksi, v=0.32) is loaded with a 40-lb horizontal force and a 25-lb…

A:

Q: R.75 00.63 THRU $5 01.123 0.250 E 1.38 0.63 mm radius hole partially through the part 0.63 mm radius…

A:

Q: Orthographics: Add missing lines and complete any missing views. Draw the isometric

A: The missing lines of the given views are shown below.

Q: Show a scale diagram indicating a reading of 0.206 inch in a micrometer.

A: Given question : Show a scale diagram indicating a reading of 0.206 inch in a micrometer.   The…

Q: In order to measure an external tapered angle you must have A. The sine bar and gage blocks B. Two…

A:

Q: What did you put in the calculator to get the box answers? Please put exactly what you put

A: The solution provided in the previous response is as follows.

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: The height (in mm) for a 125 mm sine bar to measure a taper of 27'32' on a flat work piece (correct…

A: Given:Length of sin bar, L=125 mmθ=27o 32'θ=27+3260oθ=27.533o

Q: How many balls of 50 mm diameter fit in a volume of 1910 L

A: Given:-Diameter of ball (d) = 50 mmVolume of container (V) = 1910 literTo Find :-Number of such…

Q: Read the metric caliper in millimeters. Take note that the numbers marked on the main scale are in…

A: The given scale is simple vernier caliper reading. Whose least count is given LC= 0.05 mm  And the…

Q: Create a table showing wrench sizes in metric and U.S. units.

A: Following are the wrench sizes in metric and U.S. units.

Q: Z is incorrect

A:

Q: A shift lever ball has diameter 2.535 in. What is its volume in cubic inches

A: Given   Diameter, d = 2.535 in       Radius, R = 1.2675 in Find    Volume, V

Q: Express the quantity 254,998m in mm.

A: To convert meter quantity into millimeter one must be familiar with the no. of mm exist in one…

Q: If the horizontal distance was measured to be 130m and the inclination angle was 25 degrees, what is…

A: Considering a line AB having an inclination angle with horizontal of 25 degrees. The horizontal…

Q: Read the following millimetric vernier caliper setting 005mm Answer with units:

A: Vernier caliper reading = reading of main scale + reading of other scale (where the two lines are…

Q: By and bx are labeled wrong

A:

Q: If gear 1 turns 620 degrees, how many degrees will gear 3 turn? N1 =20, N2

A:

Q: Finish the Orthographic drawing

A: Please refer the following Front view, right hand side view and top of the given isometric view. 1…

Q: Read the following inch vernier caliper setting 8. 1/128in

A: Solution: