Four gears are attached to a circular shaft and transmit the torques shown in the figure. The allowable shear stress in the shaft is 20,000 psi.8000 lb-in.19,000 lb-in.4000 lb-in.A7000 lb-in.ВCD(a) What is the required diameter d of the shaft (in inches) if it has a solid cross section?in.(b) What is the required outside diameter d (in inches) if the shaft is hollow with an inside diameter of 1.8 in.?in.

TAB=-8000TBC=-8000+19000=11000TCD=-8000+19000-4000=7000Max torque…

Answered: re attached to a circular shaft and…

re attached to a circular shaft and transmit the torques shown in the figure. The allowable shear stress in the shaft is 20 8000 lb-in. 19,000 lb-in. 4000 lb-in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A solid aluminum shaft 2 inches in diameter is subjected to two torques. Determine the maximum shearing stress in each segment and the angle of rotation of the free end. Use G = 4 × 106 psi.
A circular steel tube of length L = 1.5 m is loaded in torsion by torques T (see figure). T r2 (a) If the inner radius of the tube is r, = 41 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y, (in radians) at the inner surface? (Enter the magnitude.) rad (b) If the maximum allowable shear strain is 0.00026 rad and the angle of twist is to be kept at 0.45° by adjusting the torque T, what is the maximum permissible outer radius (r,)may (in mm)? mm Enter a number.
The compound shaft, composed of steel, aluminum, and bronze segments, carries the two torques shown in the figure. If Tc = 250 lb-ft, determine the maximum shear stress developed in each material. The moduli of rigidity for steel, aluminum, and bronze are 12 x 10° psi, 4 x 10° psi, 6 x 10° psi, respectively. %3D 500 lb • ft Tc Aluminum Steel Bronze 1.0 in. 41.0 in. D A 2 in. B 6 ft H 4 ft le– 3 ft
Situation 5 A steel shaft with a constant diameter of 50 mm is loaded as shown by applied torque. Use G=83 GPa. Solve for the total angular deformation. 800 N-m 1300 N-m 1200 N-m 2 m 1.5 m 3 m
QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is applied to the end B of the shaft. Determine the rotation of section B. The shaft and beam are made of an aluminium alloy for which E= 720 GPa and G = 27 GPa, Neglect the strain energy of the hub DF. IC 400 mm 200 mm- 40.0 mm D 60.0 mm 400 mm 800 mm HO H 30.0 mm T= 2.00 kN.m
A cylindrical pressure vessel having a radius r = 14 in. and wall thickness t = 0.625 in. is subjected to internal pressure p = 375 psi. In addition, a torque T = 90 kip-ft acts at each end of the cylinder (see figure). (Assume that the structures behave linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain the resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) T T (a) Determine the maximum tensile stress o, and the maximum in-plane shear stress T in the wall of the cylinder. max max (Enter the magnitudes in ksi.) ksi = Tmax ksi (b) If the allowable in-plane shear stress is 4.5 ksi, what is the maximum allowable torque T? (Enter the magnitude in kip-ft.) | kip-ft (c) If T = 150 kip-ft and allowable in-plane shear and allowable normal stresses are 4.5 ksi and 11.5 ksi, respectively, what is the minimum required wall thickness (in inches)? in.
A solid 1.4 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3500 Ib-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 610 rpmn? What is the maximum shear stress developed in the shaft? Answer: P = hp T= psi
A solid 1.4 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 2600 Ib-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 500 rpm? What is the maximum shear stress developed in the shaft? Answer: P = hp T = psi
A solid 2.1 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3200 Ib-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 690 rpm? What is the maximum shear stress developed in the shaft? Answer: P = hp T= psi
A punch for making holes in steel plates is shown in Figure 3. Assume that a punchhaving diameter d = 20 mm is used to punch a hole of 8 mm plate. If force, V = 110 kNis required to create the hole, determine the shear stress in the plate.
184 What is the strain energy of the massless stepped bar as shown in the figure below? [Take E= 200 GPa] (a) 0.38 N-m (c) 0.50 N-m 30 mm 10 mm 100 mm 20 mm 120 mm • ** ** 80 mm 10 kN (b) 0.42 N-m (d) 0.56 N-m
A solid 1.8 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3500 Ib-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 560 rpm? What is the maximum shear stress developed in the shaft? Answer: P = hp T = psi