Radius Angle of intersection Degree of curvature External distance Middle ordinate Arc length

Q: An image of a hilltop is 87.5 mm from the centre of a photograph. The elevation of the hill is 665 m…

A: Focal length f=210 mm, Image height r = 87.5 mm Elevation h = 665 mm Flight altitude H = 4660 mm

Q: M1 5 m -D 3 m M2 4 m M3

A:

Q: e section are given by the table. The beam is subjected to the concentrate the couple moment Mo…

A:

Q: A steel tape with a coefficient of linear expansion of 0.0000116/1°C is known to be 50m long at…

A: The coefficient of linear expansion is α=0.0000116/°C. The initial temperature is Ts=23°C. The…

Q: 4. Why the lines on the graph do not pass through the origin?

A: When any graph line does not pass through the origin, it means that when the input equals…

Q: 2. Find the Maximum Shear and Moment. 50 N A 15 N/m B D LLLL 5 m 1000 N.m -3m+! 5 m EL F 5m + 5m +

A:

Q: R=6 cm T. 5 cm 2 cm 8 cm (a)

A:

Q: The drag racer P starts from rest at the start line S and then accelerates along the track. When it…

A:

Q: Q4- Draw ILD for Ra, Rb,Vc, Mc,Vb- and Vb+ C D 3 RA a b B RB E

A:

Q: Locate the centroid of the plate area: (All units are in mm). y 500 50 80 - 140 140- 80 - 400 60 500…

A:

Q: 1. Question 1: Influence Lines on a Gerber Beam (CLO 5 Students are able to apply the concept of…

A:

Q: Find the centroidal distances from x axis and y axis

A: Consider the figure,

Q: Refer to the Ø.8740 ±.0005 dimension. What is the dimension @ MMC and @ LMC ? Name the geometric…

A: Calculate @ MMC as follows. @ MMC=Ø0.8740 +0.0005=Ø0.8745 Therefore, the @ MMC is Ø0.8745.

Q: The length of a line AB measured with a 50-m tape is 364.85m. When the tape is compared with a…

A:

Q: What type of meridian does the figure represent? W- S Meridian O True Meridian O Assumed Meridian…

A: To determine which of the following meridian is show in the figure.

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 5)…

A:

Q: + 30 mm 60 mm 20 mm 10 mm 70 mm 3. 20 mm 70 mm

A: centroid: It is a center point of an object

Q: origin: center of quarter circle R2 calculate: total area (mm2) centroid along x axis…

A:

Q: The timber beam in Figure 2 is simply supported at points A and E. The cross-section of the beam…

A:

Q: A 50-m steel tape weighing 2.42kg is of standard length under a pull of 13kg, supported for full…

A: Length of tape needs to be corrected because of different type of problems like temperature,…

Q: O dind sthen pHoduuced iuen jarce 20KN 1Ro mm 2

A: Given data : Force (F)=20 KNArea (A)=120 mm2

Q: Define matrix's diagonal, off-diagonal, subdiagonal, and superdiagonal elements. Illustrate each.

A: An n×n matrix, or a matrix with the same number of columns as rows, is known as a square matrix.

Q: The drag racer P starts from rest at the start line S and then accelerates along the track. When it…

A: The given data is: Distance, d=103 m Speed, v =41 m/s Acceleration, a=9.3 m/s2

Q: State of S and T during Spanish colonization

A: Brief concept- Spanish colonization- The arrival of Miguel López de Legazpi's expedition from Mexico…

Q: 80 30 60 90 -20- 30 Dimensions in mm

A: Dividing the figure in small figures ,and knowing the areas and centroidal distances of those…

Q: The unit used for long distances and in measuring the sides of large tracts of land kilometer yards…

A: We have to asked long distance measuring unit. We Explain that

Q: Two points on a line is to be measured by surveyors for the purpose of creating a path. After a…

A: Finding out actual length of the line.

Q: Q3- Draw ILD for Rb, Rd, Rf, Rh,Vc, Mc, Vf- and Vf+ d a 2.0m b 3.0m с 2.0m 2.0m e (hinge) 6.0m f A…

A:

Q: Locate the centroid of the plate area: (All units are in mm)

A: Centroid xcoordinatex=∑ Aixi∑ Ai Centroid y-coordinatey=∑ Aiyi∑ Ai

Q: 2) The circumference of a circle is 407. Its area is ..... ...

A:

Q: What type of meridian does the figure represent?

A:

Q: Two points on a line is to be measured by surveyors for the purpose of creating a path. After a…

A: Question is based on survey using tape.It is given that length of tape found to be too short .…

Q: A 50-m steel tape weighs 0.05kg/m and is supported at its end points and at the 10-m and 30-m marks.…

A: Given data  Tape weight Standard pull Number of spans To find Actual distance

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.