R10- 2 Holes 10 10 33 60° 13 Machin 24 10 +, Convert projections to isometrics 52 R5- -26

Q: Q1) Draw the following two dimensional model using AutoCAD commands? Ellipse(major diam. 70, minor…

A: Given:- Draw the given two dimensional model using Autocad command.

Q: sketch the orthographic view using catia v5, and i need the orthographic view in the first angle…

A: THIS FIGURE SHOWS THE ISOMETRIC VIEW AS GIVEN IN QUESTION AND DRAWN IN CATIA V5

Q: Unspecified radii R5 Draw 1-Front section 2-Half-cut side projectio 3-Pure projection

A: 1.  front section view

Q: Q1/Water.p=1.94 slugs/ft and v=0.000011 ft/s, is pumped between two reservoirs at 0.2 ft's through…

A: To find: The pump horsepower. Given: The density of water is ρ=1.94 slugs/ft3. The kinematic…

Q: Chnpter 2 Basic Knowledge of Orthogonal Projection 2 E n iR Draw the three views of the components…

A:

Q: Q1] draw the following figure three projections with scale 1:1 R8 50 16 15. 22 25 60 1.0 80

A: Orthographic projections are the perpendicular lines originated from the object and intersects from…

Q: Engineering graphics. .ORTHOGRAPHIC PROJECTIONS Creo practice exercise Using the Creo parametric…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Find Projections drawing?

A: Projection is the method used in mechanical drawing to draw a 3D object in the 2D plane for better…

Q: Deduce the third projections from the following two rectifiers

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: 15 D 4 holes 15 Deep 75R 20 50D 35 Deep BRACKET Draw the three Principal Views and Section. Include…

A: Draw three principal views and include all the dimensions.

Q: Draw the three elevations (front, side, and top) of the following geometry using AutoCAD

A: According to the details provided in the question, we need to calculate three views.

Q: 45 D30 $55 R10 4-018 15X 50 21 41 425 100 21 142 85

A: According to the details provided in the question, we need to draw a sectional  view

Q: Create an accurate pictortial

A: Find Create a pictorial view of the object.

Q: Find the front, side, and top projection

A: Solution: The Front, Side and Top view are shown below:

Q: 10 10 Base plate. Figure out the three views of the above figure , sketch the arrangement in first…

A:

Q: Draw the section view (locate the section line/cutting line along midpoint of dim 71 ) with…

A: The sectional view is drawn by constructing the solid model and sectioning it. The various…

Q: Orthographic view of the following sketch

A:

Q: R 19- $10 LJØ20 T6 19 38 63 76

A: The hand drawn third angle projection of top view, front view and side view is given below.

Q: Draw the three elevations (front, side, and top) of the following geometry using AutoCAD

A: Find Find the front view, Side view, and top view.

Q: Draw three views of the wedge block. Dimension the object using datum dimesnioning

A: The required orthographic views of the given object are drawn with true dimensions shown in the…

Q: Write the position equation (vector loop equation) for the figure given below__ prieenigna…

A: In the given there is three loop. In vector loop equation, the link connected by joints form loop,…

Q: Draw Front, Top and Right Side views of the following object with a completed dimensions. Draw in…

A: orthographic orthographic is the three view drawing of 3D object which consist front view, side view…

Q: In circular motion vr=0 vr=v theta vr=-v theta ar=0 The right representation of r-theta coordinates…

A: In a circular motion,Vr=0 because when particle is moving in a circular motion then in radial…

Q: * ifr = 8 sec0 then the cartesian equation is x^2+y^2=8 O Non of the above O y=8 (x-1)^2+y^2=64 O…

A: Here ,x=rCos(theta)=8sec(theta)*cos(theta) x=8*1/cos(theta)*cos(theta)=8 x=8....(1) And…

Q: Draw the top, front, and side view with dimensions. (Third angle view). Hint: You may draw the…

A: To find: Top view Front view and side view The direction of front view is shown below by red mark

Q: Angle (degrees) 701 60 50 40 30 20 10 0. N extension flexion use graphical method to draw velocity…

A: The above diagram shows the graph between knee angle during gait and percentage of gait cycle.The…

Q: Figure 1 shows an object; draw without dimensions: 1- Sectional front view. 2- Top view. 3-…

A:

Q: draw the isometrc view in first angle proection using catia v5

A:

Q: Xz s 10 2x, + 5x, s 60 X, + x2 s 18 3x, + x2s 44 y X, 2 0, x, z 0.

A: In maximization problems, a feasible region needs to be calculated. One of the corner points of the…

Q: P4 P3 P2 P1 7.5 25 35 Using the turning method, write down the positions of the five points shown in…

A: In absolute Co-ordination System, position of all points are referenced from origin, I have taken z…

Q: 45 TV Ø55 $30 4-018 R10 15 15 FV 50 41 RSV 42.5 100 21 142 85

A: orthographic views  are the two dimensional representation of a 3 dimensional object. The three…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.