R1 A/D Card 9-14 V R2

Q: Q4. a) With the aid of sketches, explain the concepts of the negative and positive feedback. b)…

A: Feedback (a)Negative Feedback:Concept: Negative feedback reduces the gain of an amplifier but…

Q: Digital instruments are better than Analog instruments justify this with any four features

A: The features of the digital system are discussed below:

Q: For the op-amp in Figure 4, find the value of V2.

A: Operational amplifier-An integrated circuit which amplifies weak electric signals into a strong…

Q: An ammeter of range 1-10 Amp, the accurate of ±0.3 of full scale deflection, what is the possible…

A:

Q: The three resistors are: R, = R3 R4 100N The strain gauge (RsG) with the following characteristics…

A:

Q: For the circuit given in Figure 2, with R₁ Draw the output voltage waveform at point A. =2k,…

A: According to the question, for the circuit shown belowWe need to draw the output waveform.

Q: 2. (A rectifier is a device that converts an oscillating two-directional alternating current (AC)…

A: The objective of the first part of the question is to find the output DC voltage and the peak…

Q: Calculate the maximum load current ILmax in mA if E=12V, R=170 ohm, that will ensure that the…

A: We need to find out maximum load current for given voltage regulator .

Q: Q1: Identify each of the op-amp configurations in below (a) (b) www. R₁ R₁ (c) R₁ www www R

A: Given: Op-amp configurations, To do: To identify op-amp configuration.

Q: Explain how you would set up the power supply to supply +10V/0V/-10V as used for op-amp circuits

A: A three-terminal device with two high impedance inputs is known as an operational amplifier. It is…

Q: 2-Does an n- channel JFET require a positive or negative value Tor 3-How is the drain current…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: In Full Bridge arrangement of strain measurement, supply voltage is of 1.7 V and resistance of each…

A: The solution is given below.

Q: Q2) For the circuit in the figure below, calculate the input power, output power, and power handled…

A: Given: A power amplifier circuit.  According to question:  The peak input voltage is calculated…

Q: An analogue indicating instrument with a scale range of 0-5A shows a current of 2.4A. A current has…

A:

Q: Which of the following statements about resistive transducer instrumentation is true? Strain gauges…

A: A resistive transducer instrument is used to measure the load, pressure or displacement.

Q: R

A: Since you have asked a multiple question, we will solve the first question for you. If you want any…

Q: VOLTAGE COMPARATOR +12 V Determine the gain of the circuit, G the output voltage, Vo and the…

A: A voltage comparator using op-amp is an open loop circuit with a dual input supply. There are two…

Q: ösaly äbäi On the circuit board in figure below, what happens if the middle lead (wiper) of the 100k…

A:

Q: Am I correct in saying this inverting amp gain is 10 and the expected voltage out is 10 or am I…

A: Inverting Operational Amplifier: One of the simplest and most often used op-amp topologies is the…

Q: Q2. Calculate the resolutions for the 8-bit, analog-digital converter: Input and output signal…

A: Given, An analog to digital converter has, Voltage range, Vr=10 V (0 to 10 V) Number of bit, n = 8…

Q: Connect a thermistor (Resistance=500 – 1%  per oc ) in a bridge (power supply =9V) with an…

A:

Q: The samples of analog signal is converted to digital signals by using which of the following…

A:

Q: Figure Q1(c) shows a 4-bit digital-to-analogue converter of type R-2R ladder. Given the converter…

A:

Q: 27. To achieve an output of 10 V with an input of 300 mV, what voltage gain is required?

A: Given : output voltage=10 V Input voltage =300 mV or 300 x 10^-3 V To find Voltage gain Formula used…

Q: 1. Determine the minimum and maximum output voltages for the voltage regulation in Figure below.…

A: Given R1=220 ΩR2=5 kΩ

Q: +12U R, 2.2kA +9U, Joc R2 22te LM324N GND Ru 2.2ŁA 2.2Ł2

A:

Q: An n-c nmon connguratio (Rp) 61 2.2kN and its transconductance is 3mSiemens. When input voltage is…

A: Given RD = 2.2 Kohm,  gm = 3 mS Vi = 200 mV To find output voltage Vo

Q: ng measurements with an op-amp, it was observed that input base currents were 6µA ffset current in…

A:

Q: 1. The 10M resistor (all resistor values are in Ohms and M = million) represents a scope input…

A: For 1st

Q: Refer to figure below. Determine the following: (a) VRI and VR2 (b) Current through Rf (c) Vour (d)…

A:

Q: Compute the value of vx for the multiple op-amp circuit in Figure 2. 100ko 1000 100 1000 3ma (4) 1k0…

A: Brief description : Operational amplifier is an active component which is used as followings  Adder…

Q: An op-amp is usually a differential amplifier having O Single input and two outputs always O Dual…

A:

Q: c) The following stiff voltage-divider circuit in Figure Q2 (c) consists of BJT with DC gain 140.…

A: The solution is given below

Q: A 4-digit Digital voltmeter with a 100 mV lowest full-scale range would have a sensitivity of how…

A: Given, A 4-digit DVM with, Minimum full scale value = 100 mV Resolution of this DVM is 0.0001.