R-4.3 A cantilever beam is loaded as shown in the figure. The bending moment at 0.5 m from the sup- port is approximately: (A) 12.7 kN m (B) 14.2 kN m (C) 16.1 kN m (D) 18.5 kN m 456 A 4.5 kN 1.8 kN/m -1.0m- -1.0 m-1.0 m-3.0 m- B

R-4.3 A cantilever beam is loaded as shown in the figure. The bending moment at 0.5 m from the sup- port is approximately: (A) 12.7 kN m (B) 14.2 kN m (C) 16.1 kN m (D) 18.5 kN m 456 A 4.5 kN 1.8 kN/m -1.0m- -1.0 m-1.0 m-3.0 m- B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.13.4P: A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h =...

See similar textbooks

Similar questions

A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h = 120 mm and h1= 100 mm. The maximum allowable bending stress in the plastic beam is emix = 6 M Pa, and the bending moment is M = 150 N · m. Determine the minimum permissible width bminof the beam.
A beam supporting a uniform load of intensity q throughout its length rests on pistons at points A, C and B (sec figure). The cylinders are filled with oil and are connected by a tube so that the oil pressure on each piston is the same. The pistons at A and B have diameter d1and the piston at C has diameter D2. (a) Determine the ratio of d2to d1so that the largest bending moment in the beam is as small as possible. Under these optimum conditions, what is the largest bending moment Mmaxin the beam? What is the difference in elevation between point C and the end supports?
The horizontal beam ABC of an oil-well pump has the cross section shown in the figure. If the vertical pumping force acting at end C is 9 kips and if the distance from the line of action ofthat force to point B is 16 ft, what is the maximum bending stress in the beam due to the pumping force?
A C 200 x 17.1 channel section has an angle with equal legs attached as shown; the angle serves as a lintel beam. The combined steel section is subjected to a bending moment M having its vector directed along the z axis, as shown in the figure. The cent roi d C of the combined section is located at distances xtand ycfrom the centroid (C1) of the channel alone. Principal axes yl and yvare also shown in the figure and properties Ix1,Iy1and 0pare given. Find the orientation of the neutral axis and calculate the maximum tensile stress exand maximum compressive stress if the angle is an L 76 x 76 x 6.4 section and M = 3.5 kN - m. Use the following properties for principal axes for the combined section:/^, = 18.49 X 106 nrai4,/;| = 1.602 X 106 mm4, ep= 7.448*(CW),_r£ = 10.70 mm,andvf= 24.07 mm.
A simple beam ACE is constructed with square cross sections and a double taper (see figure). The depth of the beam at the supports is dAand at the midpoint is dc= 2d 4. Each half of the beam has length L. Thus, the depth and moment of inertia / at distance x from the left-hand end are, respectively, in which IAis the moment of inertia at end A of the beam. (These equations are valid for .x between 0 and L, that is, for the left-hand half of the beam.) Obtain equations for the slope and deflection of the left-hand half of the beam due to the uniform load. From the equations in part (a), obtain formulas for the angle of rotation 94at support A and the deflection Scat the midpoint.
A frame ABCD is constructed of steel wide-flange members (W8 x 21; E = 30 x ID6 psi) and subjected to triangularly distributed loads of maximum intensity q0acting along the vertical members (see figure). The distance between supports is L = 20 ft and the height of the frame is h = 4 ft. The members are rigidly connected at B and C. Calculate the intensity of load q0 required to produce a maximum bending moment of 80 kip-in. in the horizontal member BC. If the load q0 is reduced to one-half of the value calculated in part (a), what is the maximum bending moment in member BC? What is the ratio of this moment to the moment of 80 kip-in. in part (a)?
Draw the shear force and bending moment diagrams for the beam with loading shown below, P= 16 kN, w= 30 kN/m, M=40 kN.m. Also, state the maxmium shear force and bending moment in the text box. (Upload the diagrams showing all key values with units as well as neat and clear calculations) P kN P kN w kN/m M KN.m A 0.5 m 1 m 1 m- 1 m- -1 m
Draw the shear force and bending moment diagrams for the beam shown in your solution sheets. Determine the maximum positive shear force in kips. Determine the maximum negative shear force in kips. Determine the maximum positive bending moment in kip-ft. Determine the maximum negative bending moment in kip-ft.* Determine the point of inflection from point C in feet.
An A-36 steel beam of following cross section is part of a bridge and it is subjected loading as shown. mmmmm 35 ft 250 lb/ft 10 in 35 ft 50 ft 25 in 600 lb/ft * Assume that the bridge has a self-weight of 250 lb/ft and due to the truck, the loading is now 600 lb/ft for the 50 feet section as shown in the picture above. Now if the maximum bending moment due to the truck is 865.625 kip-ft, that translates to a maximum bending stress as shown in the table below. 25 in 50 ft 35 ft Maximum Bending stress (kpsi) Cross-sectional shape Yield strength of steel Moment of inertia of beam A-36 9.97 kpsi Rectangular I-shaped Beam 36 kpsi 36 kpsi 21.633 kpsi The cross-sectional dimensions of both shapes are shown below. 250 lb/ft 10 in 35 ft (in) 13020 6290 Consider yourself as an engineer assigned to this bridge construction and discuss the suitable options for the optimal cross-section of the bridge. Note that from the data shown in the table, both rectangular and I-beam cross-sections have…
Calculate the support reaction forces at A and B for the beam? and the question stated in the attatched question.
Draw the shear force and bending moment diagrams of the given simple headstock beam? can you solve it step by step!
PLEASE ANSWER THIS URGENT. I WILL SURELY UPVOTE!!!